Zoom Power Drive PD-01 Operation Manual Download Page 16

16

ZOOM Power Drive PD-01

Safety Precautions

In this manual, important information that is intended to prevent the danger of injury to persons and
damage to equipment is marked with special symbols. The meaning of these symbols is explained
below.

Please observe the following safety tips and precautions to ensure hazard-free use of the PD-01.

Using an AC adapter to power this unit is recommended. When powering the
unit from a battery, an alkaline battery should be used.

AC adapter operation

Use only an AC adapter rated for 9 V DC, 300 mA, center minus (Zoom

AD-0006). Using the unit with a different adapter poses a risk of fire and
electric shock.

Connect the AC adapter only to an AC outlet that supplies the rated voltage

required by the adapter.

When disconnecting the AC adapter from the AC outlet, always grasp the

adapter itself.

Disconnect the AC adapter when not using the unit for an extended time. 

Battery operation

Use a generic 9V dry battery (6F22) (alkaline or manganese). 
The PD-01 is not designed to charge batteries. Observe the precautions on

the battery.

Remove the battery when not using the unit for an extended time.
If battery leakage has occurred, wipe the battery compartment and the

battery terminals carefully to remove all remnants of battery fluid.

While using the unit, the battery compartment cover should be closed.

Avoid using the PD-01 in environments where it will be
exposed to: 

Temperature extremes
High humidity or moisture
Excessive dust or sand
Excessive vibration or shock

The PD-01 is a precision instrument. Except for the foot switch, do not push

other parts with your feet or subject them to strong force.

Take care that no foreign objects (coins or pins etc.) or liquids can enter the

unit.

Be sure to turn the power to all equipment off before making connections.
Before moving the unit, turn the power off, disconnect all cables and the

AC adapter.

Never open the case of the PD-01 or attempt to modify the product in any

way since this can result in damage.

ZOOM does not accept responsibility for any damage caused by alteration

of the unit.

ZOOM CORPORATION
NOAH Bldg., 2-10-2, Miyanishi-cho, Fuchu-shi, Tokyo 183-0022, Japan
PHONE: +81-42-369-7116 FAX: +81-42-369-7115
Web Site: http://www.zoom.co.jp

Printed in Japan PD-01-5000-2

About power

Usage environment 

Handling

Alterations

Disregarding instructions printed here incurs the risk of

death or severe injury to persons.

Disregarding instructions printed here incurs the risk of

injury to persons and/or damage to peripheral equipment.

Summary of Contents for Power Drive PD-01

















Reviews: