Accurately imitating the AED Plus requires that instruc-
tors be familiar with the protocol currently followed by the
AED Plus for
PUSH HARDER
and
GOOD COMPRESSIONS
prompts.
For further information about the functioning of the
clinical AED Plus, see the AED Plus Operator’s Guide and Admin-
istrator’s Guide.
The Remote Controller lights indicate the current training
settings while the Trainer2 simulates the actual AED Plus behavior.
The Remote Controller will turn itself off after 10 seconds.
The Trainer2 will remember the last scenario setting which will re-
appear the next time the
view/enter
button is pushed.
NOTE
SCENARIOS
VF 1
VF 2
VF 3
VF 4
Done
Shock
CPR
Shock
CPR
1
Simulated heart rhythm: Student Response:
ASYSTOLE 1
ASYSTOLE 2
VF 1
VF 2
Done
No Shock
CPR
Shock
CPR
2
Simulated heart rhythm: Student Response:
VF 1
VF 2
NSR 1
NSR 2
Done
Shock
CPR
No Shock
CPR
3
Simulated heart rhythm: Student Response:
ASYSTOLE 1
ASYSTOLE 2
ASYSTOLE 3
ASYSTOLE 4
Done
No Shock
CPR
No Shock
CPR
4
Simulated heart rhythm: Student Response:
SETUP and TEST
1
SELECT SCENARIO SETTINGS
2
Scenario 3: SHOCK - NO SHOCK
Scenario 2: NO SHOCK - SHOCK
Scenario 1: SHOCK - SHOCK
Manual Scenario mode
CONTROLS / INDICATORS
Handheld Remote Controller:
PUSH HARDER
prompt
(only when metronome is beeping)
NO
SHOCK
advised on next heart analysis
(manual mode only)
Pads
attached/not attached to victim’s bare chest
(toggle-switch)
CPR Metronome
set up to beep or not beep
(Real CPR Help
®
during CPR interval)
Push to turn Trainer2 on
Push again to start current scenario
(as defined using Remote Controller)
Hold to turn Trainer2 off
ZOLL AED Plus Trainer:
View/Enter
scenario
Show current scenario selection (press once)
Start scenario (press again)
Move Up
to next scenario.
Scenario 4: NO SHOCK - NO SHOCK
Scenario Set-up Controls
:
Training Controls:
GOOD COMPRESSIONS
prompt
(only when metronome is beeping)
Pause
(resume) current scenario
End
current scenario
Green light remains on = Trainer2 is on and ready for use
Green light off = Trainer2 is turned off or has no battery power
Red Light steady = Last command from Remote Controller accepted
Red Light 3 flashes = Last command from Remote Controller is invalid
NOTE
Install 4 “D” batteries in the AED Plus Trainer2.
Trainer2 unit:
Action:
Press
On/Off
button to turn Trainer2 on.
Green light turns on, indicating Trainer2 is
ready for use.
Remote Controller:
Install 2 “AA” batteries in handheld remote.
Turn the Remote Controller on by pushing the
view/enter
button.
Point Remote Controller at unit and press
view/enter
button again. Green light on Remote
Controller will show Manual Scenario Mode is
selected.
Manual Scenario Mode
View/Enter Button
Trainer2 unit:
Action:
Turn Trainer2 unit off (hold down
On/Off
button).
Setup test is now complete. Trainer2 unit and
Remote Controller are ready for use.
Trainer2 unit:
Action:
Turn Trainer2 on by pushing the
On/Off
button.
Action:
Remote Controller:
Action:
Press
view/enter
button once to turn on Remote
Controller.
Use
move up
button to select desired scenario.
Use CPR Metronome button to turn Real CPR Help
(beeping) on or off for this scenario.
Push
view/enter
button once to enter scenario for
AED Plus Trainer2.
CPR PROMPTS
3a
Remote Controller:
Action:
The Remote Controller controls all prompts when
the Trainer2 is beeping (during the CPR interval).
NOTE
SCENARIO CONTROLS
3
Remote Controller:
Action:
VF (Ventricular Fibrillation-shock advised) is the
default simulated heart rhythm in Manual Scenario.
Analysis - VF
For the next analysis to result in NO Shock advised,
push the
NO Shock
button.
NOTE
Once the No Shock button has been pushed, the next
simulated heart analysis will advise NO Shock. This setting cannot be
reversed for the next analysis.
In all scenarios the
Pads
buttton must be pressed
once to proceed with analysis. If pressed again, it
will begin to prompt for attaching pads.
PAUSE/STOP SCENARIO
3b
Press the
PUSH HARDER
button during the CPR
interval to force the unit to say “Push Harder”.
Press the
GOOD COMPRESSIONS
button during the
CPR interval to force the unit to say “Good
Compressions”.
Remote Controller:
Action:
In all scenarios (manual and automatic), the rescue
can be paused by pushing the
Pause/Resume
button once. Push it a second time to resume the
scenario.
Trainer2 unit:
Action:
The PUSH HARDER and GOOD COMPRESSIONS
buttons are only valid during the CPR interval.
The red light on the Trainer2’s status window emits
one long flash if the prompt is currently valid.
If the PUSH HARDER or GOOD COMPRESSIONS
buttons are pushed when the Trainer2 is not
beeping, the unit’s red light emits three quick
flashes, indicating that the prompt is currently
invalid.
In all scenarios (manual and automatic), the rescue
can be ended by pushing the End button once.
NOTE
4
On
Off
On
Off
On
Off
On
Off