manualshive.com logo in svg

Zodiac HPO, Instructions For Installation And Use Manual, Page: 22 / 28

Share
Download
Zodiac HPO Instructions For Installation And Use Manual Download Page 22

21

EE22

High voltage protection

The power supply is incorrect.

 

Replace the printed circuit board.

The power board is faulty.

 

Replace the printed circuit board.

EE23

Compressor start-up error

The power board is faulty.

Check the printed circuit board.

Accumulation of liquid and gas.

 Check the power supply voltages

The voltage is unstable.

 

Check the voltage.

EE24

Ambient temperature or printed circuit 

board

Ambient temperature or input water 

temperature too low.

 

Check and replace the printed 

circuit board.

EE25

Compressor power error

The compressor operates with 1 or 2 

phases.

 

Check the wiring.

EE26

4-way valve inversion error

Blockage-inversion of the 4-way valve.

Switch to heating/cooling mode to 
check inversion of the valve.

 

Replace the 4-way valve.

Low refrigerant (no d5-TH2 or d3-TH1 

detection).

 

Check refrigerant levels.

EE27

EEPROM memory data error

Data loss in the memory.

 

Reload the data to the memory.

Printed circuit board error.

 

Replace the printed circuit board.

EE28

Communication error with the controller

Printed circuit board error.

Off/on to restart.

 Check and replace the 

printed 

circuit board.

Summary of Contents for HPO





























Reviews:

No comments