Zmotion EIO16084 Manual Download Page 20

Page: 20 / 35

EIO16084 Bus Expansion Module User Manual V1.5

Reserved

Note:



ALM, ENABLE, CLR and INP are recommended to be used as axis IO, because the

drive capacity is small.



OVCC, +5V are only used for communication between the controller and the

servo driver, please do not use it as power supply for other places.

3.6.1.

AXIS Interface Signal Specification & Wiring

→

Specification:

Signal

Item

Description

PUL/DIR

Signal type

Differential output signal

Voltage range

0-5V

Maximum frequency

10MHz

EA/EB/EZ

Signal type

Differential input signal

Voltage range

0-5V

Maximum frequency

5MHz

IN16-23

Input method

NPN leak type, it is triggered

when low electric level is input.

Frequency

＜

5kHz

Impedance

6.8KΩ

Voltage level

DC24V

The voltage to open

<10.5V

The voltage to close

>10.7V

Minimal current

-1.8mA (negative)

Maximum current

-4mA (negative)

Isolation

optoelectronic isolation

OUT8-15

Output method

NPN leak type, it is 0V when

outputs

Frequency

＜

8kHz

Voltage level

DC24V

Maximum current

+50mA

Overcurrent protection

Summary of Contents for EIO16084




































Search results

Summary of Contents for EIO16084

Reviews:

Related manuals for EIO16084

Brands by name

Popular brands

Zmotion EIO16084, Manual

Search results

Summary of Contents for EIO16084

Reviews:

Related manuals for EIO16084

Brands by name

Popular brands