Zmotion ECI1000 Page 9 Hardware Manual Download | Manualshive

Page: 9 / 25

background image

ECI1000 Network Motion Control Card Hardware Manual Version1.4

9

2.1.1

Order Information

Model

Specification

ECI1300

3 axes, point to point, electronic cam, doesn’t support interpolation

ECI1302

3 axes, point to point, electronic cam, linear interpolation

ECI1306

3 axes, point to point, electronic cam, linear interpolation, circular

interpolation

ECI1308

3 axes, point to point, electronic cam, linear interpolation, circular

interpolation, continuous interpolation

ECI1400

4 axes, point to point, electronic cam, doesn’t support interpolation

ECI1402

4 axes, point to point, electronic cam, linear interpolation

ECI1406

4 axes, point to point, electronic cam, linear interpolation, circular

interpolation

ECI1408

4 axes, point to point, electronic cam, linear interpolation, circular

interpolation, continuous interpolation

«
...
7
8
9
10
11
...
»

Summary of Contents for ECI1000


























Reviews:

No comments

Related manuals for ECI1000

Brand: ABC Design Pages: 38

Brand: easydriver Pages: 26

Brand: Calsense Pages: 10

Brand: ABC Design Pages: 10

Brand: ABC Design Pages: 10

Brand: CAME Pages: 18

Brand: CAME Pages: 28

Brand: CAME Pages: 28

Brand: CAME Pages: 4

Brand: CAME Pages: 40

Brand: CAME Pages: 26

Brand: CAME Pages: 34

Brand: CAME Pages: 2

Brand: Danfoss Pages: 32

PVG 16 PVH/Covers

Brand: Danfoss Pages: 112

Brand: Danfoss Pages: 44

PVG 16 PVH/Covers

Brand: Danfoss Pages: 144

Brand: Danfoss Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands