ZKX Audio MT 1000 User Manual Download Page 11

- page 9 -

#9

SAFETY PRECAUTIONS FOR ALL VOLTAGES!

WARNING- TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE

Do not allow water or liquids to be spilled into this unit. If the unit has been exposed  to rain or liquids, please unplug the power cord immediately from the 
outlet (with DRY HANDS) and get a qualified service technician to check it. Keep this unit away from heat sources such as radiators, heat registers, stoves, 
etc. This unit contains no user – serviceable parts. Refer all service needs to qualified service engineer through a ZKX dealer. 

This triangle with an arrow similar to a flash of lightning that appears on your component alerts you to the presence of uninsulated “dangerous voltage” inside 
the enclosure that may be sufficient to constitute a risk or shock.  The triangle with an exclamation mark was designed to point out the need to read carefully 
the repair and maintenance instructions in this accompanying literature.

¡WARNINGS!

The equipment must be located near an easily accessible power outlet.
The equipment does not have to be exposed  to dripping or splashes and  do  not place objects filled with liquid, such as vases or 
glasses, on the apparatus.
If the feeder is damaged, do not  use the product. In this case the cable must be replaced by the manufacturer or authorized technical 
personnel.
Do not expose the unit to flame or intense heat sources. Do not place lighted candles or any other similar objects on the apparatus, 
which must not  be reached by direct sunlight either.
Do not install the appliance in a confined space since it needs a suitable ventilation. Do not place it on carpets, armchairs, as well as 
on other soft or  uneven surface. Do not cover the ventilation of the apparatus with newspapers, folders, tablecloths, etc.  
Make sure it has a good stability. Avoid placing it on an inclined surface.
Do not expose it to mechanical vibrations or blows
Do not change the plug or use adapters. If your residential installation  does not have power outlets which can be compatible with the 
plug, go to a  registered electrician who will make the necessary changes in your electrical sytem.  

CAUTION

TO REDUCE THE

 

RISK OF ELECTRIC SHOCK, DO NOT REMOVE

 COVER (OR BACK). NO USER –SERVICEABLE PARTS INSIDE.

REFER SERVICING TO  

QUALIFIED SERVICE PERSONNEL.

USER`S MANUAL MT

,

 MTs and MTc SERIES

USER`S MANUAL MT

,

 MTs and MTc SERIES

Summary of Contents for MT 1000



















Reviews: