background image

Reader: 

The reader reads the data in the card and sends it to the controller. 

Control panel: 

The control panel is the system’s control center that receives signals from the access 

controller, performs logical judgment and processing of these signals, and sends executive 
commands to the electric motor. 

IR sensor:

 anti-pinch function. 

        

 

1.5 The working principle of swing barrier turnstile system   

1)

 

After powered on, the system performs self-check. If no failure is detected, the machine starts to 
operate normally. If a failure is detected, the system displays related messages on the LCD 
display screen so that the user can have a quick knowledge of and solve the problem. 

2)

 

When the reader detects a valid card, the buzzer will give a nice audible prompt to the 
pedestrian, indicating that the card is being read successfully. And then, the reader sends signals 
to the access controller to request permission to pass through the passage. If the signal is legal, 
the access controller will send the open signal to the master control panel. 

3)

 

After receiving the signal from the access controller, the control panel sends valid control signals 
to the electric motor and opens the barrier. 

1.6 Product related parameters 

Dimension(mm) 

SBT1000S:      L=200,   W=185,   H=1100 

Input voltage 

AC100-120V/200-

240V,50-60Hz 

Output voltage 

DC 24V 

Input control signal 

Switching signal 

Relative humidity 

20%-93% 

temperature 

-28

-60

 

Pass speed 

Maximum: 30/minute 

Infrared sensor 

Working 

environment 

Indoor/Outdoor

If shelter

 

Air switch 

Access controller 

IR Sensor 

24V power supply 

Motor 

Encoder 

Control board 

Clutch 

Reader 

Summary of Contents for SBT1000S












Reviews:

Related manuals for SBT1000S