ZKTeco PB3000 Series User Manual Download

Page: 5 / 16

PB3000 User Manual

1.3 Working Principles

Power subsystem

: The motor and gearbox provide power for the whole system.

Speed reduction subsystem

: The speed reduction system controls the lifting and falling speed of the boom.

It makes the boom slow down when the boom stops movement.

Spring balance subsystem

: The compression spring provides balance for the weight of the boom to keep

the boom horizontal.

Electric control subsystem

: The electric control subsystem consists of a control board and a position sensor.

1.4 Specification Parameters of Product Series

Appearance

Model

Boom Type

Standard Boom Length

Lifting/

Falling

Speed

Fastening

Mode

Note

Gray

appearance

series

PB3010L

Straight boom

3.2 M

1.8s

Cabinet on

the left

There are 200V
and 100V types
for the device.

PB3010R

Straight boom

3.2M

1.8s

Cabinet on

the right

PB3030L

Straight boom

4.5M( main boom 3.2m + vice

boom 1.5m

Cabinet on

the left

PB3030R

Straight boom 4.5M( main boom 3.2m + vice

boom 1.5m

Cabinet on

the right

PB3060L

Straight boom

6M( main boom 3.2m + vice

boom 3m

Cabinet on

the left

PB3060R

Straight boom

6M( main boom 3.2m + vice

boom 3m

Cabinet on

the right

Summary of Contents for PB3000 Series

















Search results

Summary of Contents for PB3000 Series

Reviews:

Related manuals for PB3000 Series

Brands by name

Popular brands

ZKTeco PB3000 Series, User Manual

Search results

Summary of Contents for PB3000 Series

Reviews:

Related manuals for PB3000 Series

Brands by name

Popular brands