6
5
8.
Equipment Communication
PC
1. TCP
/
IP Communication
2. RS485
Communication
The PC software can communicate with the panel according to the communication protocols (RS485 and TCP/IP) for data
exchange and remote management. The communication cable should be as far away from high-voltage lines as possible.
Do not keep the communication cable in parallel with power cords or bind them together.
1) Internationally accepted RVVP (shielded twisted-pair) wires should be used for communication to effectively avoid
of bus cascade connection.
interference. RS485 communication wires should be connected by means
3) One RS485 bus may hold 63 control panels, but it is not recommended to connect with less than 32
.
access control panels
4)For the inBIO reader connection, if the reader and the control panel use the same power, it is recommended that the wire
5) To enhance the stability of communication
t is necessary to keep
When the wire is longer than 300 meters, i
2) It is recommended that the RS485 bus should be less than 600 meters to help aid communication stability.
(120 ohm) of the two devices to the system. As shown in the figure above, turn number 8 of the DIP switches of
number 8 switch of the first and the last control panel at “ON” status. That adds the RS485 terminal resistance
should be less than 100 meters. If greater length is required, please use a separate power supply.
The following is “wet mode” lock connection with external power
Insert a screw driver to the rectangular hole in the four corner of the
panel
back. Push it in until hearing the
"
click
"
sound. Then remove the case from the panel.
7.485
Reader (inBIO Reader)
Connection
the 1
#
and 8# at "ON” status.
+
+
+
-
-
NC
NO
GND
COM
SEN
+
+
-
-
FR107
FR 107
-
LED
1
2
3
4
5
NO Lock
LOCK
LOCK
Enlarged diagram
of lock terminals
NC Lock
Lock Power
Diode
Diode
Jumper
terminal
PC
485+
485-
GND
485+
485+
485+
485-
485-
485-
GND
GND
GND
Serial Bus
485
Converter
DIP Switch
8# Control Panel
2# Control Panel
1# Control Panel
1
2
3
4
O
5
6
7
8
N
E
X
T
R
S
4
8
5
P
C
R
S
4
8
5
S
T
A
T
E
PWR
S
W
IT
C
H
SGND
E
X
T
R
S
4
8
5
P
C
R
S
4
8
5
S
T
A
T
E
PWR
S
W
IT
C
H
SGND
E
X
T
R
S
4
8
5
P
C
R
S
4
8
5
S
T
A
T
E
PWR
S
W
IT
C
H
SGND
Switch
8# Control Panel
1# Control Panel
2# Control Panel
E
X
T
R
S
4
8
5
P
C
R
S
4
8
5
S
T
A
T
E
PWR
S
W
IT
C
H
SGND
E
X
T
R
S
4
8
5
P
C
R
S
4
8
5
S
T
A
T
E
PWR
S
W
IT
C
H
SGND
E
X
T
R
S
4
8
5
P
C
R
S
4
8
5
S
T
A
T
E
PWR
S
W
IT
C
H
SGND
supply.
+12V
GND
#3 Reader
+12V
GND
485-
GND
485+
#1 Reader
#2 Reader
#4 Reader
（
Separate power supplies
）
（
Separate power supplies
）
PC
S
T
A
T
E
PWR
E
X
T
R
S
4
8
5
P
C
R
S
4
8
5
S
W
IT
C
H
The control panel supports inBIO biometric verification reader and Wiegand reader. All inBIO reader operations are executed
For reader 1, 2 (the odd number is for entered reader, and the even number is for exit reader), the door number is 1. And the
485 address is 1, 2, as in the figure below. For more information, please refer to the software user manual.
from the control panel including storage, verification, etc. Re-register the fingerprints is not required when replacing the reader.
For example, use the FR1200 reader , the standby current is less than 100mA, the max current is less than 120mA, When
using the separately power supplies, to make sure the steady operation.
Besides, a single EXT485 interface can supply maximum500m
A(1 2V) current . So the entire cuttent consumption
should be less than this max value when the readers
share
power
with
the
panel
.
In calculation,
more than twice of normal
please use max current
of
the
reader
,
and
start
current
is
usually
work current, please consider of this situation.
inBIO reader connection:
First of all, set the 485 address (device number) of the reader by DIP switch and software.
Attention:
DIP
switch
configuration
for
FR
1200,
KR
500
E
&
M
-
RS
;
Software
configuration
for
unnormalized
F
11,
MA
300
and
other
fingerprint
readers
.
the device
is
start, Instantaneous current
can reach 240 mA. As inBIO reader, consider the starting current is
bigger
,
onnect
through the EXT485 interface can only c
two readers for
power supply
.
So
the
power
of
control
panel connect only
For some of the devices with much greater consumption, we suggest to
nearest 2 readers.
