background image

It  is  recommended  that  the  device  must  be  installed  on  a  horizontal  solid  platform  with  a  height  of  
50mm to 100mm.

1.

After  installation,  check  if  the  connection  has  been  done  correctly  at  the  connecting  points  of  the 
ground wire, at the connector assemblies and wiring points of the circuits, as well as at each movable 
part of the device. Any loose nuts, screws and other fasteners should be tightened in time to avoid any 
failures caused by long-time operations. 

4.

1

1  Installation Requirements 

3.

Make  sure  the  ground  wire  of  the  system  is  reliably  connected  to  avoid  personal  injuries  or  other 
accidents.

2.

It

 

is

 

also

 

recommended

 

that

 

the

 

device

 

should

 

not

 

be

 

used

 

in

 

the

 

corrosive

 

environment

.

2  Preparation

To install the device you must have:

A Screwdriver:

 To remove or install the screw on the device. 

A Pencil: 

To mark the device  size and the screw hole. 

A Electric Drill:

 To drill holes in accordance to the marked screw holes. 

A Wrench:

 To secure the M12 expansion screw on the device.

A Tapeline:

 To measure the dimensions that need to be measured during the installation of the device.

A Hex Wrench: 

To remove or install the screw on the device. 

Except for the hex wrench, all other tools should be prepared on your own.

Note:

 

The FHT2300 series, FHT2300D series, FHT2400 series and FHT2400D series have only slight differences 
in  appearance,  but  the  installation,  wiring  and  use  are  the  same,  and  the  following  is  an  example  of 
FHT2300 series.

Summary of Contents for FHT 2300D













Reviews:

Related manuals for FHT 2300D