WIRING DIAGRAM
ACCESSORIES
CONTROL PANEL
Model
Part No. Description
CP-E
2012032
CONTROL PANEL E WITH STANDARD CABLE 15 M
DU-E
2012033
DISTRIBUTION UNIT E WITH POWER CABLE 6 M
DU-EX
2012034
DISTRIBUTION EXPANSION UNIT E WITH POWER CABLE 6 M
IT400-E
2012215
INTERCEPTOR 400 E WITH CABLE 3 M & CABLE COVER
IT600-E
2012018
INTERCEPTOR 600 E WITH CABLE 3 M & CABLE COVER
IT800-E
2012019
INTERCEPTOR 800 E WITH CABLE 3 M & CABLE COVER
IT1000-E
2012020
INTERCEPTOR 1000 E WITH CABLE 3 M & CABLE COVER
IT600-E TUNNEL R500
2012021
INTERCEPTOR 600 E TUNNEL R500
WITH CABLE 3 M & CABLE COVER
IT600-E TUNNEL R600
2012022
INTERCEPTOR 600 E TUNNEL R600
WITH CABLE 3 M & CABLE COVER
IT600-E TUNNEL R800
2012023
INTERCEPTOR 600 E TUNNEL R800
WITH CABLE 3 M & CABLE COVER
IT400-E CHINE PORT
2012216
INTERCEPTOR 400 E CHINE PORT SIDE
WITH CABLE 3 M & CABLE COVER
IT400-E CHINE STBD
2012217
INTERCEPTOR 400 E CHINE STARBOARD SIDE
WITH CABLE 3 M & CABLE COVER
IT600-E CHINE PORT
2012024
INTERCEPTOR 600 E CHINE PORT SIDE
WITH CABLE 3 M & CABLE COVER
IT600-E CHINE STBD
2012025
INTERCEPTOR 600 E CHINE STARBOARD SIDE
WITH CABLE 3 M & CABLE COVER
EC1.5-M12
2011258
M12 EXTENSION CABLE 1.5 M
EC3-M12
2011259
M12 EXTENSION CABLE 3 M
EC5-M12
2011260
M12 EXTENSION CABLE 5 M
EC10-M12
2011261
M12 EXTENSION CABLE 10 M
EC15-M12
2012038
M12 EXTENSION CABLE 15 M
EC20-M12
2012039
M12 EXTENSION CABLE 20 M
SC15-M12
2012037
M12 STANDARD CABLE 15 M
CP ALU FRAME
2011281
CONTROL PANEL ALU FRAME
CP COVER
2011381-
2011385
CONTROL PANEL COVER
WHITE, LIGHT GRAY, MID GRAY, DARK GRAY, BLACK
CC-EX
2012036
CABLE COVER EXTENSION E KIT
GPU
2011240
GLOBAL POSITIONING UNIT WITH CABLE 5 M & MOUNT KIT
GB
2011622
GIMBAL BRACKET FOR CONTROL PANEL
All readings must be green!
Corrective action is always necessary when excessive torque levels are observed.
The root cause is usually the flatness of the transom behind the interceptor and/
or excess antifouling between its blades.
IMPORTANT
Always use the controls to move the interceptor blades. Never try to force
the interceptor blades by hand.
5
6
1
2
Snap on the frame
Apply sealant (x4)
When waterproofing
is required
Control panel:
T10 (ST 2.9x19)
(x4)
INTERCEPTOR CHECK
4 INITIAL START
Press and hold the POWER/MENU button until the
Zipwake logo appears on the display and follow
the steps on the screen.
Carry out an Interceptor Check to verify function imme-
diately after installation and before launching the boat.
Repeat this before every launch.
NOTE!
Interceptor Check will not start if no interceptor
configuration has been saved to the system (refer to the
Operator's Manual).
The check repeats a 5 stroke sequence, where each interceptor blade is extended,
one by one, from port to starboard and then retracted in the same order. Visually
confirm that the interceptors move accordingly during the check. This confirms
that the interceptors are correctly connected to the distribution unit(s).
SET UP THE SYSTEM
Refer to the Operator’s Manual for detailed information about setting up
and operating the system.
1
5
2
4
6
7
8
3