To install ZIPLink module, insert upper tab
into DIN rail.
Rotate
until
firmly seated
Click
DIN Rail Installation
and Removal
Repeat for Tab 2.
Tab
1
Tab
2
and locked
on DIN rail.
To remove ZIPLink
module, insert
screwdriver
between Tab 1
and module.
Pry up
to release
clip from DIN rail.
Note: For
cable/wire
clearance
requirements see
specifications.
3505 Hutchinson Road, Cumming GA30040
1-800-633-0405 www.automationdirect.com
Copyright 2008, AutomationDirect.com Incorporated/All Rights Reserved Worldwide
6/23/2009 Document # ZL-RTB50 Rev3
WARNING:
To minimize the risk of potential safety problems, you
should follow all applicable local and national codes that regulate the
installation and operation of your equipment. These codes vary from
area to area and it is your responsibility to determine which codes
should be followed, and to verify that the equipment, installation, and
operation are in compliance with the latest revision of these codes.
Equipment damage or serious injury to personnel can result from
the failure to follow all applicable codes and standards. We do not
guarantee the products described in this publication are suitable for
your particular application, nor do we assume any responsibility for
your product design, installation, or operation.
If you have any questions concerning the installation or operation
of this equipment, or if you need additional information, please call
Technical Support at 770-844-4200.
This publication is based on information that was available at the
time it was printed. At AutomationDirect.com® we constantly strive to
improve our products and services, so we reserve the right to make
changes to the products and/or publications at any time without notice
and without any obligation. This publication may also discuss features
that may not be available in certain revisions of the product.
Specifications
Description*
50-Pole Connector Module for interfacing
SureServo I/O to a controller
Approvals
File # E200031 UL, cUL, Class 1, Division 2,
Groups A,B,C,D Hazardous Locations,
CE, EN 61131-2:2007
Operation Voltage**
0-30VDC
Voltage Rating
24VDC
Maximum Current per Circuit
0.2A
Maximum Current per Module
10A
Number of Terminal Block Positions
50
Surrounding Temperature Range
32 to 140°F (0 to 60°C)
Terminal Block Contacts
Copper alloy, tin-lead plated
Wire Range (Rated Cross Section)**
12-24AWG Solid or Stranded Copper Conductor
(2.5mm²)
Wire Strip Length
0.24-0.27” (6-7mm)
Screw Torque
4.4 in-lbs (0.5 Nm)
Connector Type
3M mini DELTA Ribbon (MDR), 101 Series, 50
pin Example: Plug 10150 - 3000VE,
Shell 10350 - 52A0 - 008
Dimensions (WxHxD)
5.46” x 1.89” x 1.87” (138.6mm x 48.1mm x
47.5mm)
Connecting Cable (Sold separately)
ZL-SVC-CBL50 (0.5m/1.6ft)
ZL-SVC-CBL50-1 (1m/3.3ft)
ZL-SVC-CBL50-2 (2m/6.6ft)
Cable/Wire Cleareance
4.00” (101.6mm) top and bottom
Mounting Restrictions
None
Description
The ZL-RTB50 is a DIN rail mounted feed through
module designed to interface the SureServo
servo drive analog and discrete control signals to
a PLC or other controllers by connecting the
ZL-SVC-CBL50 cable between the SureServo
CN1 connector and the ZL-RTB50 connector.
Cables
The ZL-SVC-CBL50 is available in three lengths.
• ZL-SVC-CBL50 0.5m (1.6ft)
• ZL-SVC-CBL50-1 1m (3.3ft)
• ZL-SVC-CBL50-2 2m (6.6ft)
Feedthrough Connector Module
Installation Instructions
ZL-RTB50
HAZARD WARNING
A. THIS EQUIPMENT IS SUITABLE FOR USE IN CLASS I, DIVISION
2/ZONE 2, GROUPS A, B, C AND D OR NON-HAZARDOUS LOCATIONS
ONLY.
B.
WARNING – EXPLOSION HAZARD –
SUBSTITUTION OF COMPO-
NENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION 2/ZONE 2.
C.
WARNING – EXPLOSION HAZARD –
DO NOT CONNECT OR DIS-
CONNECT CONNECTORS OR OPERATE SWITCHES WHILE CIRCUIT
IS LIVE UNLESS THE AREA IS KNOWN TO BE NON-HAZARDOUS.
D. ALL MODULES USED WITH ACCESSORIES MUST USE R/C (ECBT2)
MATING PLUG FOR ALL APPLICABLE MODELS. ALL MATING PLUGS
SHALL HAVE SUITABLE RATINGS FOR DEVICE.
*Connecting cables are for internal wiring only.
**Use Class 2 power supply. Use conductors rated 60°/75°C.
