TRADEMARKS
Zipato and the Zipato logo are registered Trademarks. All
other product names mentioned herein may be trademarks or
registered trademarks of their respective companies.
NOTICE
Although Zipato has attempted to ensure the accuracy of the
content of this manual, it is possible that this document may
contain technical inaccuracies, typographical, or other errors.
Zipato assumes no liability for any error in this publication, and for
damages, whether direct, indirect, incidental, and consequential
or otherwise, that may result from such error, including, but not
limited to loss of data or profi ts. Zipato provides this publication
“as is” without warranty of any kind, either express or implied,
including, but not limited to implied warranties of merchantability
or fi tness for a particular purpose. The published information in
the manual is subject to change without notice. Zipato reserves
the right to make changes in the product design, layout, and
driver revisions without notifi cation to its users. This version of the
Installation guide supersedes all previous versions. The product
ELECTROMAGNETIC COMPATIBILITY
In proper state and when operated properly, the product complies
with all the requirements in respect of interference radiation
according to EN 301 489-17, EN 301 489-1 and EN 300 328. The
connections conducting HF signals must neither be manipulated
nor damaged.
PACKAGE CONTENT
1PC
Micromodule Quad
1PC
Screws pack
1PC
Sticker pack
1PC
Quick Installation Guide
FEATURES
Door/Window, motion, temperature and illuminance sensor
It consists of two parts, magnet and a sensor
New Z-Wave 500 series chip supports multichannel operation
and higher data rates (9.6/40/100kbps)
Higher output power enhances communication range(+5dBm
output power as compared to -2.5dBm 300 series)
Can be used with various Z-Wave networks/controllers
Low battery battery indication
Door/Window status and battery status auto-report
LED indicator
Over-the-air fi rmware update
Tamper proof protection
SPECIFICATION
TECHNICAL SPECIFICATION
Protocol
Z-Wave Plus
Power
CR123A lithium battery, 1400mAh
Operating voltage
3V
Operating current
45 mA
Low battery voltage
2.6 V
Operating temperature
C
Temperature detect range
0°C ~ 40°C
Temperature detect accuracy
±0.5OC
Range
Minimum 30m indoor / 100m outdoor
Illumination range
0 - 100%
WAKE
When it powers up, the device will be in wake state for about 20
seconds. During this period, the controller can communicate
with the device. Normally the device is always sleeping to save
the battery energy.
FUNCTION DIP SWITCH
There is a function DIP switch in front of the device. Remove the
front cover at the right top of the PCB, and also has mark “M1”
and “M2” for two switches.
M1
M2
Description
ON
ON
Test Mode and OTA mode.
ON
OFF
Normal Mode.
OFF
ON
Normal Mode.
OFF
OFF
Customer Mode. According to the
confi guration setting NO. 5 to set the
operation mode.
INSTALLATION
First you have to add device to the Z-Wave network. First,
make sure the primary controller is in inclusion mode. Power on
the device, after removing the insulation Mylar on the back side
of the device. The device will auto start the NWI (Network Wide
Inclusion) mode. It should be included in 5 seconds. You will see
the LED light ON one second.
Let Controller associate with Group 1 of the device, any light
switch that should be turned on when the device is triggered
should be associated with Group 2 of the device.
In the package there are two type of double coated tape, one is
thicker (hereinafter referred to as A tape) and another is thinner
(hereinafter referred to as B tape), you can use A tape for the test
at the beginning. The right way for A tape installation is to stick it
below the tamper key. The thicker tape won’t let the tamper key
close, so the sensor will enter the test mode, You may test if
installed position is good or not by this way.
Replace the new battery and install the cover back.
1. Put the front cover bottom to 1-1, and press down.
2. Push the front cover top to 2-1.
POWER UP PROCEDURE
BATTERY POWER CHECK
When it powers up, the device will detect the power level of the
battery immediately. If the power level is too low, the LED will
continue to fl ash for about 5 seconds. In that case, replace the
battery.
PIR WARM UP
When it powers up, the PIR need to warm up before operation. The
warm up time about 1 minute, the LED will fl ash every 2 seconds.
After completing the procedure the LED will light ON three times
NWI
When it powers up, the device will check iif it is already added to
the network. If it isn’t, it will automatically start the NWI mode. The
LED will fl ash in every second and continue for about 30 seconds,
until timeout or successful inclusion by controller. You can press
the tamper key 3 times to abort the NWI mode.
Door/window functions. The benefi ts of combining Door/
window with PIR in one sensor can be observed in the following
scenarios:
A
The ambient lighting would be lower than default setting
value after sunset. If the Multisensor Quad was installed on the
inner side of door in the house, Multisensor Quad would detect
coming in people, then the light would be turned on for the better
illumination by radio transmission. Furthermore, Multisensor
Quad can be applied in a bathroom and it may turn on/off light
and fan automatically.
B
Multisensor Quad can be taken as a portal chime at front
desk of hotel or restaurant by sending out signal to IP-Gateway
PSC01 as reminder which can be connected with speaker to turn
the volume up. It can be kept silent when customer leaving.
C
For SMEs (Small and medium enterprises), Multisensor
Quad plays an important role in working hours and non-working
hours. When non-working hours, Multisensor Quad plays as
security motion sensor, protects the offi ce from intruders.
At working hours, 4 in 1 sensor, can be applied to curtain or
heater/cooler controller for energy saving issue; although some
people may use thermostat to control heater/cooler however,
Multisensor Quad sensor can be smarter choice. Since it can
detect the people’s, activities, and shutdown machine when no
one exists or no movements.
D
In the past, a digital home starter KIT includes many different
sensors with very high price. Right now, Using the 4 in 1 patented
sensor and a 4 in 1 gateway PSC01 (Siren + s light +
IP based controller) carry out home “security” + “safety” +
“automation” in one box and provide customer full experience
of digital life and fl exibility in installation with affordable price.
SECURITY NETWORK
This device supports the security function. When the device is
included with a security controller, the device will auto switch
to the security mode. In the security mode, the following
commands need to be wrapped in Security Command Classes to
communicate, otherwise there will be no response.
MULTISENSOR
QUAD
QUICK INSTALLATION GUIDE
v1.5
OVERVIEW
FIGURE 1
Dimensions (unit: mm)
TAKE CARE OF YOUR SAFETY
Display extreme caution when using ladders or steps, please
follow manufacturer’s instructions. Be careful when using hand
and power tools and follow the manufacturer’s guidelines when
using them. Take care that the correct tools are used. Wear
goggles or protective clothing where required.
INTRODUCTION
Presence detector, temperature meter, illuminance meter and
door/window sensor in one device. Zipato Multisensor Quad offers
elaborate security and ambient sensing options. Multifunctional
nature of this product allows you to detect motion, monitor
opened/closed status of any opening object, measure room’s
ambient temperature and light intensity.
When the detector is paired with security appliances, the (1) Door/
window or (2) PIR sensor act as an alarm detector. Alternatively,
when the detector is paired with Z-Wave controller, the detector
can support home automation by detecting both changes in PIR
motion detect, door/window open close status and lux levels, in
percentage. Example scenario: During night, if illuminance levels
are lower then preset value, any person movement in device’s fi eld
of vision will trigger radio signal that will turn connected lightning
equipment. In second example, you can combine door/window
sensor and illumination sensor, and temperature sensor, so when
person opens the door, lights will turn on, and heater/cooler will be
activated to adjust room’s temperature to comfortable levels.
This product can be included and operated in any Z-Wave network
with other Z-Wave certifi ed devices from other manufacturers
and/or other applications. All non-battery operated nodes within
the network will act as repeaters regardless of vendor to increase
reliability of the network.
The device adopt the Z-Wave 500 series chip, which brings
following advantages:
Concurrent multi-channel support reduces external
interference.
Better RF range, improves about 10 meters in indoor.
Supports 100 Kbps transmission speeds.
PIR detection range
7m
PIR detection angle
90 Deg.
Weight
49g
Dimensions
Sensor 28x95x23mm; Magnet 12x47x9 mm
Package weight
68g
Package dimensions
68x21x136 mm
Battery
1500mAh
Magnetic gap
20 mm
Warranty
1 year
MODELS AND FREQUENCIES
Australia
ph-psm02.au / 919.80 MHz , 921.40MHz
European Union
ph-psm02.eu / 868.40 MHz, 869.85 MHz
India
ph-psm02.in / 865.20MHz
Israel
ph-psm02.is / 916.00 MHz
Russia
ph-psm02.ru / 869.00 MHz
United States
ph-psm02.us / 908.40 MHz, 916.00 MHz
BATTERY INSTALLATION
When the device reports the low battery message. The user
should replace the battery.
To open the front cover please follow below steps.
Using a tool (1) to press 1-1 till you hear a click sound
Hold the front cover and pull back
Hold the front cover and pull up
Back view
Testing Sponge
After fi nishing the test and deciding right position you can remove
tape A, and mount the sensor by using tape B. This will close the
tamper key and let the sensor enter normal mode.
CHOOSING A SUITABLE LOCATION
The recommended mounting height is 160cm
Don’t let the device face the window or the sunlight.
Don’t let the device face the source of heat. For instance the
heater or the air-condition.
APPLICATION
Multisensor Quad is a special device combining both PIR and
1.
2.
3.
4.
5.
6.
7.
8.
9.
ILLUMINATION
SENSOR LENS
28.00
3
Profi le
view
50.00
10.00
28.00
96.00
1
Front view
2
Back view
12.35
4
Top/bottom view
1
2
2
3
1-1
2
1
1-1
2-1
documentation states a Security Enabled Z-Wave Controller must
be used in order to fully utilize the product.
