background image

Page 4 of 12 

Zip FlushMaster Pearl Installation & Maintenance Instructions - 82902 - January 2012 v1.00

Set Up Water Discharge 

Single stall
1.5 to 2.5 Litre
Discharge Capacity

Twin stall
3.0 to 5.0 Litre
Discharge Capacity

Triple stall
4.0 to 7.5 Litre
Discharge Capacity

Single stall

Twin stall

Single trough
Maximum trough
length 600 mm

Twin trough
Maximum trough
length 1200 mm

Single trough
1.5 to 2.5 litre
discharge capacity

Single trough
3.0 to 5.0 litre
discharge capacity

Single trough
4.0 to 7.5 litre
discharge capacity

Typical Installation with Cistern

Typical Installation with Direct Injection

Flow restrictor Installation Notes:

-The Restrictaflow must be fitted between 

the isolating valve (not supplied) and the 
latching valve (see page 5).

-The Restrictaflow is designed to save water 

and to reduce the flow, particularly 
when used on single stall installations.

-The Restrictaflow may be drilled out (in 

0.5mm increments) or removed when 
servicing multiple stalls and a higher 
flow is required, or when there is 
insufficient water pressure. 

-The Restrictaflow is normally required 

with operating pressures greater than 
700kPa.

-An Isolating valve must be supplied 

and installed in accordance with AS/
NZS3500

Summary of Contents for FlushMaster Pearl













Reviews: