manualshive.com logo in svg

Zimmer Biomet Persona, Surgical Technique, Page: 6 / 72

Share
Download
Zimmer Biomet Persona Surgical Technique Download Page 6

4 | 

Persona

®

 Revision Knee System

 

Surgical Technique

Quick Reference:  

Instrumentation Overview

Attaches to:

•  Tibial and femoral impactor pads

•  Tibial central and perimeter cone 

impactor heads

•  Femoral central and metaphyseal 

cone impactor head

•  Persona Primary Femoral 4-in-1 

Cut Block

Attaches to:

•  Stem extractor

•  Stem provisionals

Removes the:

•  Tibial and femoral 

provisionals

•  Persona Primary 

Femoral 4-in-1 Cut Block

•  Cone provisionals

Removes the: 

•  Pin puller

Attaches to:

•  Canal Reamers

•  Stem extension post

•  Broach pilot adapter

•  Cannulated reamers

•  Tilt reamers

•  5 mm hex driver

•  Tapered stem drill bits

Removes the:

•  Reamers

•  Stem extension post  

and broach pilot adapter

•  Tapered stem drill bits

Slap Hammer

Quick Connect (QC) Handle

T-Handle

 

Note:

 Do not use implants and/or instruments from other knee systems unless expressly labeled for such use.

 

Note:

 Do not use implants and/or instruments from the Persona Revision Knee System with other knee 

systems unless expressly labeled for such use.

Summary of Contents for Persona









































































Reviews:

No comments