(Please refer to “Intend to quit a network and change the network”)
Delete or move to reset: push the switch button 5 times and hold at the end for 3
INSTALLATION INSTRUCTIONS
-03-
-01-
INSTALLATION
ZB15R
Voltage............................................................................................120VAC, 60Hz
Incandescent...............................................................................................1000W
Resistive.............................................................................................1800W(15A)
Motor.............................................................................................................1/2HP
ZigBee frequency..............................................................2.4GHz, IEEE 802.15.4
Wireless transmitting power..................................................................... 4.5 dBm
and the closest ZigBee receiver module, depending on your home's construction
SPECIFICATIONS
Wiring Diagram
Observe Important Wiring Information
Always follow the recommended wire strip lengths and wiring combination
when making wiring connections.You may wish to consult a electrician with
questions or for professional installation.
The wire connectors included with this receptacle are intended
to only be used with copper wire. Consult a qualified electrician if you have
aluminum wiring.
Instructions:
1. Strip insulation 3/8” for 12 or 14 AWG wire. Strip insulation 7-16'' for 16
or 18 AWG wire.
2. Hold stripped ends together in parallel and align any frayed strands (do
not twist wires).
3. Push wires firmly into connector. Twist connector clockwise with fingers
until tight. Pull wires to check for tightness.
Wire Connector / Combination Chart
One #14 w/one-to-four #16 or #18
One #12 w/one-to-three #14 or #16 or #18
Two #14 w/one-to-three #16 or #18
Two #12 w/one or two #14 or #16 or #18
You should now be able to use the front panel program button to manually
turn On/Off a lamp plugged into the Z-Wave controlled outlet.
Use your primary controller to include the receptacle in the home control
network after the receptacle is installed as shown in the above diagram.
It can then be added to groups and /or lighting scenes and managed
remotely to control the ON/OFF status of the connected lighting.
Important:
WARNING: HIGH VOLTAGE TO AVOID FIRE, SHOCK , OR DEATH,
TURN OFF THE POWER AT THE CIRCUIT BREAKER BEFORE YOU
INSTALL THIS RECEPTACLE.
OPERATIONS
Basic Operation
The connected light can be turned ON in two ways:
1. With a remote
2. Manually with the program button on the Z-Wave receptacle
Remote Control
Z-Wave remotes provide control of an Individual device,Groups of devices
and Scenes. Other brands of Z-Wave Certified remotes may not offer as
much flexibility in how you can set up your lighting control network. Please
refer to your remote control’s instructions for details on its capabilities and
instructions for adding and controlling devices.
Manual Control
The program button on the ZW15R duplex receptacle allows the user to:
1. Manually turn the connected equipment ON or OFF by pressing the
button.
2. Include or exclude the receptacle from the Z-Wave home control network
with your primary controller.
After a power failure, the ZW15R ’s Z-Wave controlled
receptacle returns to its last used ON/OFF state.
Please Note:
Operation indicator
Blue LED ON indicates Switch OFF, Blue LED OFF indicates Switch ON.
WARNINGS AND CAUTIONS
To be installed and/or used in accordance with appropriate electrical code
and regulations. Exercise extreme caution when using ZigBee devices to
control appliances. Operation of the ZigBee device may be in a different
room than the controlled appliance, also an unintentional activation may
occur if the wrong button on the remote is pressed.
ZigBee devices may automatically be powered on due to timed event
programming. Depending upon the appliance, these unattended or unint-
entional operations could possibly result in a hazardous condition.
ZigBee enabled devices should never be used to supply power to, or
control the on/ff status of medical and/or life support equipment.
If you are unsure or uncomfortable about performing the installation, please
consult a qualified electrician.
Manual Control
The switch button on the ZB15R allows the user to: Manually turn the connected
equipment ON or OFF by pressing program button. When the blue LED indicator
Ballast,CFL,LED .......................................................................................1200VA
ZigBee 15A Tamper
Resistant Receptacle
This receptacle may be used in new installations, or to replace an existing
wall receptacle.
1.
For retrofit applications, remove
the
wall plate.
2.
Warning! Verify power is OFF before continuing.
3.
Remove the existing receptacle from the box.
4.
Disconnect the wiring from the existing receptacle.
5.
Connect the ZigBee receptacle as shown in the wiring diagram: Black
lead to hot wire, white lead to neutral wire, green lead to ground wire.
6.
Check connections to be sure they are tight and that there are no bare
conductors are exposed.
7.
Insert the ZB15R receptacle into the standard outlet box carefully.
8.
Make sure the ZB15R receptacle to the box using the supplied screws
9.
Attach the wall plate.
10.
Restore power at the circuit breaker and test the system.
seconds, the blue LED will blink, the device will quit the present HA ZigBee network.
Wireless protocol............................................................................ ZigBee HA 1.2
Ground
Green
Hot
Black
Neutral
White
＜
Working environment
Humidity....................................................................................................... 85%
Temperature ...........................................................................................14~113 F
≤
control replacement of any regular receptacles to control table and floor lamps,
small appliances and more. This receptacle provides two outlets, one with
programmable functions such as scenes, association and scheduling events and
the other outlet provides constant power. The blue LED light on the face cover
indicates the status of the controlled outlet while acting as a subtle night light.
Also, this receptacle meets the 2011 NEC code requirements.
remote control function and can be registered to a ZigBee network via ZigBee
gateway. The ZigBee smart switch can easily be controlled and monitored by a
smartphone.
-02-
Distance .................. Up to 100 feet line of sight between the Wireless Controller
turns OFF, the appliance or device plugged into ZigBee controlled outlet will turn
ON, and vice versa.
。
Remote Control
Use an App on your mobile, you can control ZB15R at anywhere in a ZigBee HA
network. Please refer to your Gateway and App's instructions for details on its
capabilities and instructions for adding and controlling devices.
Add to a ZigBee network
Follow your ZigBee controller and app instructions to add a device and enter Paring
mode. Restore power to a new ZB15R on the circuit breaker for initializing network.
The ZB15R will automatically search for a compatible ZigBee network and the blue
LED indicator keeps blinking when paring with ZigBee gateway. After the ZB15R
is paired and added in the ZigBee network, the blue LED indicator will stay on
and the device would register into the ZigBee gateway.
Reset ZB15R (remove from ZigBee network manually)
To change this ZB15R from present network, use the “intend to quit network”
function to clear the register information in present network:
Push the switch button 5 times and at the end hold for 3 seconds, blue LED will
blink. ZB15R will clear the register information and quit the present HA ZigBee
network. Then you can restore the power switch on and it to add ZB15R into
other network. Please refer to your Gateway and App's instructions for details
operation of change a HA network.
Interchangeable Face Cover
Wireless Home Automation Control Device
Always-on Receptacle
ZigBee Controlled Receptacle
Program Button
Blue LED Indicator
To replace the face
cover, just use a
flat screwdriver to
pry-off the
interchangeable
face
cove
r
.
FEATURE
S
Perfect replacement for regular receptacles, 120VAC, 15 Amp
Tamper-resistant (TR) receptacles keep you and your family safe
Manual and remote on/off control to any connected lighting and other electrical
load with moible or other controller in the ZigBee HA compliant network
Interchangeable color face cover
ZigBee HA protocol, automatic access to ZigBee network, no need to pair codes
scene mode, apps and cloud control is available
Reduce energy consumption and enjoy wireless home automation
Indoor use only
DESCRIPTION
The ZB15R TR duplex receptacle is the perfect wireless manual and remote on/off
This ZB15R TR duplex receptacle is a US standard wall mounted switch with ZigBee
