ZIEHL-ABEGG MPG-1000V Operating Instructions Manual Download Page 4

Electrical equipment must be checked regularly: Loose connections are to be re-
tightened and damaged lines or cables must be replaced immediately.

Never clean electrical equipment with water or similar liquids.

A separate fault and performance monitoring-system with an alarm signal function is 
necessary in order to prevent personal injuries and material damages during 
malfunctions and in case the device fails. Substitute operation must be taken into 
consideration!

Intended use

These devices are intended exclusively for measured value acquisition of differential 
pressures (non-aggressive gases). Their operation is only permitted under observance 
of the speci

cations in these operating instructions.

Any other use above and beyond this will be considered as improper use. The manufac-
turer will not be liable for any damage resulting from this. The company using it bears the 
sole risk.

3 Product overview

3.1 Function

Differential-pressure sensors in proven ceramic-cantilever technology for climate and 
clean-room application.
The measured differential pressure (air and non-aggressive gases) is transformed into 
an output signal proportional to the measuring range.
The range from 50 Pa to 6000 Pa is covered with 3 types of device. With each type four 
measuring ranges over DIP switch are selectable.
The differential pressure sensor supplies a proportinal output signal when the pressure 
at the 

Plus

- connection exceeds the pressure at the 

Minus

-connection.

3.2 Storage

The device must be stored in its original packaging in a dry and weather-proof room.

Avoid exposure to extreme heat and cold.

Avoid over-long storage periods (we recommend a maximum of one year).

3.3 Disposal / recycling

Disposal must be carried out professionally and in an environmentally friendly way in 
accordance with the respective national legal stipulations.

"

Separate the materials by type and in an environmentally friendly way.

"

If necessary, commission a specialist company with the waste disposal.

Operating Instructions 

MPG-..V

Product overview

L-BAL-E248-GB 1931 Index 003

Part.-No. 00163446

4/12

Summary of Contents for MPG-1000V













Reviews: