background image

-  - 

least 5 M long. Do not use the pipe if the pipe is damaged. If you want connect this machine to 
portable  water  mains,  you  must  install  a  backflow  preventer  in  the  water  pipe  to  prevent  dirty 
water  flow  back  to  the  drinking  water  system.  The  backflow  preventer  shall  comply  with  EN 
60335-2-79 ANNEX AA. 

OPERATING INSTRUCTIONS 

This unit is to be connected to a cold water source 

ONLY 

The motor of this pressure washer will NOT run. It will only operate when the trigger is 

squeezed. 

 
- Connect the outlet hose to the washer and connect the spray gun to the outlet hose. 
- Connect nozzle and nozzle extension. 
- Check gauze filter is clear of any blockage. 
- Connect the water supply hose. 
- Check that the hose has no kinks in it. 
- Turn on water and check for leaks. 
- Depress trigger to allow air to be expelled though the pump and hoses, lock trigger. 
- Plug in machine and turn on switch. 
- Unlock trigger and use the pressure washer. 

 

Shut down 

1.

 

Turn off the motor(push switch to the off position) 

2.

 

Unplug the unit from the power source. 

3.

 

Turn off the water supply. 

4.

 

Press the trigger of the gun to depressurize the system.

 

 

5.

 

Disconnect the garden hose from the pressure washer. 

6.

 

Wipe all surfaces of the unit with a damp clean cloth. 

7.

 

Engage the gun safety lock. 

CAUTION: 

ALWAYS

 turn off the unit’s motor 

BEFORE

 turning off the unit’s water supply. 

Serious damage could occur to the motor if the unit is run without water.  

CAUTION: 

NEVER  disconnect  the  high-pressure  discharge  hose  from  the  machine 

while the system is still pressurized. To depressurize the unit, turn off the motor, turn off 
the water supply and squeeze the trigger 2-3 times.

 

ADJUSTABLE SPRAY NOZZLE 

Turn off the spray lance first, hold the rear part of spray nozzle, then turn the front part of spray 

nozzle clockwise, Water may be sprayed out from the spray nozzle in fan shapes (fig 1); Turn the 

front part of spray nozzle withershins, Water may be sprayed out from the spray nozzle linearly 

(fig 2). 

Low/High Pressure Adjustable Lance 

Using High Pressure: 

Please make sure the trigger released and there is not any water spraying. then turn the rear part of 

spray nozzle withershins ( fig 4). Squeeze the trigger, the gun will spray water with high pressure. 

Using low pressure: 

Summary of Contents for ZI-5990













Reviews: