background image

The available temperature settings range from 6°C minimum to 28°C maximum. 

When the heater has been unplugged (or after a power failure), the temperature

will reset to the factory setting of 20°C.

F

USING THE TIMER

The timer allows you to switch on the heater automatically at a preset time. 

In order to switch on the timer, the correct time must have been set (refer to

Section C) and the heater should be off. Follow the procedure below:

Press the

button 

N

and then the TIMER key 

Q

immediately after that. 

The TIMER light and the 4-digit 

M

will start blinking.

Use the adjustment keys 

P

to set the time at which the heater must ignite. 

Use the key on the left (

N

hour) to set the hours and the key on the right 

(

M

min.) to set the minutes (interval of 5 minutes).

After approximately 10 seconds the 4-digit will show CLOCK again and the 

TIMER indicator light will light up, indicating that the timer function has been 

activated (Fig. G).

The timer will ensure that the room will have been heated to approximately 

the required temperature at the set time.

When you want to switch off the heater and ignite it again with the timer, all

you have to do is press the TIMER key (refer to Section G).

Press the 

button 

N

once to clear the timer setting.

G

SWITCHING OFF THE HEATER

There are two ways to switch off the heater. 

Press the 

button 

N

. The information display will show the CLOCK 

signal. Within approximately one minute the flame will have extinguished. 

Press the TIMER key 

Q

, when you want to switch off the heater and ignite it 

again with the timer the next time. This not only switches off the heater, but 

it also activates the timer function. You can change the required time with 

the adjustment keys 

P

(refer to Section F).

H

THE INFORMATION DISPLAY

The information display 

M

not only serves as an indicator of the (set) time and

temperature (sections C, E, and F), it also indicates any malfunctioning of the

heater. The code on the information display tells you what is the matter:

CODE

INFORMATION

WHAT TO DO

e -   0

Temperature within the heater too high.

Cool-down and re-ignite.

f -   0

Power interrupted.

Re-ignite the heater.

e -   1

Faulty thermostat.

Contact your dealer.

2

1

4

3

2

1

4

47

G: The TIMER indicator

light indicates that the

timer function has been

switched on.

In case of any

malfunctioning the

information display will

tell you what is the

matter.

Summary of Contents for SRE 150 E















Reviews: