Zhone AIM29000 Installation Instructions Manual Download Page 6 | Manualshive

Page: 6 / 24

background image

6

January

2006

AIM2-A2-GZ41-00

2. With the AIM29000 Printed Circuit Board (PCB) facing up and the AIM29000

faceplate model name on the right, align the edges of the PCB with the slot
module guides on both sides.

3. Slide the AIM29000 into the chassis until it is fully seated. Do not use

excessive force.

4. Tighten the fastening screws on the AIM29000 faceplate. Do not over-tighten

the fastening screws.

Verifying Power

If you have not already powered up your BLC, do so now.

The PWR (power) LED on the AIM29000 faceplate illuminates solid green to
indicate the AIM29000 is receiving power.

«
...
4
5
6
7
8
...
»

Summary of Contents for AIM29000

























Reviews:

No comments

Related manuals for AIM29000

Brand: Ubiquiti Pages: 3

Brand: Datasheen Pages: 25

Brand: Watchguard Pages: 30

SLK-R602 Series

Brand: Seriallink Pages: 29

8677 - BladeCenter Rack-mountable - Power Supply

Brand: IBM Pages: 126

Brand: 2N Telekomunikace Pages: 67

Brand: LevelOne Pages: 146

Brand: Planet Pages: 66

Brand: Honeywell Home Pages: 36

SmartNode 4634 Series

Brand: Patton electronics Pages: 12

Brand: TP-Link Pages: 2

Brand: Planet Pages: 67

Network Video Recorder

Brand: IC Realtime Pages: 118

Mobile Network Video Recorder

Brand: IC Realtime Pages: 158

Thin Twinax Terminal LM-6488

Brand: Ringdale Pages: 15

4 Channel Fan Speed Control Module CLX-1FAN4

Brand: Crestron Pages: 1

Brand: Zte Pages: 48

whitebox version 1

Brand: SamKnows Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands