background image

10

February 2002

3920-A2-GK47-10

Important Safety Instructions

1. Read and follow all warning notices and instructions marked on the product or included in the manual.

2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product

and to protect it from overheating, these slots and openings must not be blocked or covered.

3. Do not allow anything to rest on the power cord and do not locate the product where persons will walk on

the power cord.

4. Do not attempt to service this product yourself, as opening or removing covers may expose you to

dangerous high voltage points or other risks. Refer all servicing to qualified service personnel.

5. General purpose cables are provided with this product. Special cables, which may be required by the

regulatory inspection authority for the installation site, are the responsibility of the customer.

6. When installed in the final configuration, the product must comply with the applicable Safety Standards

and regulatory requirements of the country in which it is installed. If necessary, consult with the
appropriate regulatory agencies and inspection authorities to ensure compliance.

7. Input power to this product must be provided by one of the following: (1) a UL Listed, CSA Certified

power source with a Class 2 or Limited Power Source (LPS) output for use in North America, or (2) a
certified power source with a Safety Extra Low Voltage (SELV) output for use in the country of
installation.

In addition, if the equipment is to be used with telecommunications circuits, take the following
precautions:

– Never install telephone wiring during a lightning storm.
– Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
– Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at
   the network interface.
– Use caution when installing or modifying telephone lines.
– Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote 
   risk of electric shock from lightning.
– Do not use the telephone to report a gas leak in the vicinity of the leak.

Summary of Contents for 3920Plus















Reviews: