Zhejiang Feishen Vehicle FSH62832, Instruction Manual

Page: 13 / 26

Zhejiang Zhejiang Zhejiang Zhejiang Feishen Feishen Feishen Feishen Vehicle Vehicle Vehicle Vehicle CO., CO., CO., CO., LTD LTD LTD LTD....
13
13
13 13
/
26
26
26 26
Dual
Dual Dual
Dual Rates/Exponential
Rates/Exponential Rates/Exponential
Rates/Exponential Settings
Settings Settings
Settings
The aileron, elevator and rudder dual rates on the FSH62832 are simultaneously activated
by the dual rate switch. The amount of travel decrease for each control may be set
between 0% and 100% of the values set for the end points (explained in End Point
Adjustment on page 14).
Note
Note Note
Note : It is possible to set a dual rate value to zero, thus causing no response from that
channel. If the dual rates are inadvertently set to zero, a crash could result.
Note Note Note Note : When performing initial model setup, the E.P.A.s should be set prior prior prior prior to to to to setting the
dual rates. When setting the E.P.A.s for the first time on a new model, the dual rates
should be set to 100%. .
D/R D/R D/R D/R Dual Dual Dual Dual Rate Rate Rate Rate Settings Settings Settings Settings
To
To
To To select
select
select select the
the
the the Switch/position
Switch/position
Switch/position Switch/position to
to
to to control
control
control control the
the
the the dual
dual
dual dual rates:
rates:
rates: rates:
1
、
Enter
the programming mode,
press MODE" MODE" MODE" MODE"▲ ▲ ▲ ▲" """ or or or or " """▼ ▼ ▼ ▼" """ key
to access D/R programming mold
2
、
Press the “ “ “ “SELECT SELECT SELECT SELECT” ” ” ” key to choose the desired channel
(1-aileron, 2-elevator, 4- rudder). The channel number appears
on the left side of the screen
Note
：
if an “ “ “ “EXPO EXPO EXPO EXPO” ” ” ” is shown on the screen, that means you press “ “ “ “SELECT SELECT SELECT SELECT” ” ” ” too long,
and access “ “ “ “EXPO EXPO EXPO EXPO “ “ “ “ set mode. Press “ “ “ “SELECT SELECT SELECT SELECT” ” ” ” to get back to dual rate setting.
3
、
Place the dual rate switch (selected previously) in the desired position for the value you
wish to change. (generally, pilots prefer to have the switch in the “up” position for the high
rate, and in the “ “ “ “down down down down” ” ” ” position for the low rate.
4
、
Change the dual rate value for the respective channel using the DATA
DATA DATA
DATA “
“ “
“+
+ +
+“
“ “
“ or
or or
or “
“ “
“----”
” ”
” lever
until the desired control throw is achieved. If you wish to change the control throw when
the switch is in the other position as well, move the switch accordingly, then use the DATA DATA DATA DATA
“
“ “
“+
+ +
+”
” ”
” or
or or
or “
“ “
“----“
“ “
“ lever to change the throw rates.
5
、
Repeat procedure 3 and procedure 4 to set the dual rates for other channels.
(channel 2-elevator, channel 4-rudder)
Exponential Exponential Exponential Exponential Settings Settings Settings Settings
Exponential, or “ “ “ “EXPO EXPO EXPO EXPO “ “ “ “ as it is commonly abbreviated,
affects the travel of the servos around their center in
relationship to stick movement. Exponential does NOT
impact the overall travel volume of the servos. A negative
“-“ exponential input will soften or reduce the servo’s
movements near the control’s neutral position. A positive “+”
exponential input will increase the servo’s movements near the control’s neutral position.
Exponential set could between -100% and +100%.