ZF ZF 45 IV Operating Instructions Manual Download | Manualshive

Page: 22 / 26

background image

WARRANTY

22

EN 3201.758.001a 2016-02

5 WARRANTY

The marine gearbox has an identification plate stating its characteristics. If this plate is tampered with in any way or
removed the warranty will lose its validity.
The data on the plate must be quoted each time a service centre is contacted.

NOTE:

THE GUARANTEE FORM IS ON PAGE 1. THE GUARANTEE PERIOD IS AS STATED ON THE GUARANTEE FORM, WHICH MUST
BE CONSERVED TOGETHER WITH THE ON-BOARD DOCUMENTS

«
...
20
21
22
23
24
...
»

Summary of Contents for ZF 45 IV



























Reviews:

No comments

Related manuals for ZF 45 IV

Brand: ICS Schneider Messtechnik Pages: 124

Brand: Camozzi Pages: 2

Brand: Yamaha Pages: 78

Brand: Fast Pages: 42

Brand: DARAY Pages: 28

Brand: Haenim Pages: 2

Brand: Ecco Pages: 2

Brand: Landoll Pages: 94

Brand: iFIT Pages: 11

Brand: Malekko Pages: 2

Brand: Major Pages: 26

Brand: Nectar Pages: 46

Brand: Neauvia Pages: 17

Brand: Yamaha Pages: 5

Brand: RAB Pages: 4

Brand: Petromax Pages: 16

MS-1 MICRO SEQUENCER - MUSICIAN S GUIDE

Brand: Kurzweil Pages: 91

Brand: schmersal Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands