Zeta PREMIER EX8, User Manual

Page: 5 / 13

Extinguishing Panel - USER MANUAL
Approved Document No: GLT.MAN-132
PAGE 5
Issue : 1.2 Author: NRPJ Date: 06/10/2010
The Premier EX8 has the following LED indicators:-
LED COLOUR FUNCTION / MEANING
POWER GREEN The panel is supplied with power, either battery, mains or both
COMMON FIRE RED There is an alarm on the system. Check which zone caused the alarm
COMMON FAULT YELLOW There is a fault on the system. Another LED(s) will be lit to indicate the specific fault
BATTERY FAULT YELLOW There is a problem with the batteries. Rectify or replace.
CHARGER FAULT YELLOW The panel is not charging the batteries (usually mains fail or low mains)
LOW BATTERY YELLOW The batteries are below their final voltage & should be replaced
EARTH FAULT YELLOW Problem in system wiring. At least one cable is shorting to earth.
EXT.FAN DISABLE YELLOW The external equipment relay has been disabled
SYSTEM FAULT YELLOW The CPU has crashed, (Or CPU reset has been pressed & held)
REMOTE FAULT YELLOW The panel has received a fault input from external equipment
REPEATER FAULT YELLOW The panel has lost communication with the repeater panel
GEN S/C FAULT YELLOW Indicated that a line fault is caused by a short circuit
EXTINGUISHANT RELEASED RED The bottle output has been activated & the gas released
RELEASE IMMINENT RED The panel has started the release timer and will activate bottle imminently
HOLD/ABORT YELLOW An emergency hold OR emergency abort input has been activated.
MANUAL RELEASE RED A manual release call point has been activated
1
ST
STAGE ALARM RED One of the crossed zones is in alarm
2
ND
STAGE ALARM RED Both of the crossed zones are in alarm
LOW PRESSURE YELLOW A drop in bottle pressure has been detected
FLOODING ZONE FAULT YELLOW There is a fault relating to the flooding zone1 (ie the extinguishing section of the panel)
MANUAL MODE YELLOW The panel is in manual only mode (ie will not be triggered by detectors)
AUTOMATIC MODE GREEN The panel is in automatic or manual mode
GENERAL DISABLEMENT YELLOW Lights when any section of the system is disabled
GENERAL TEST YELLOW Lights when any section of the panel is in test mode
CONTROLS ACTIVE YELLOW Lights when controls enabled keyswitch is on
ZONE 1-6 FIRE RED Lights when one of the detection zones is in alarm
ZONE 1-6 FAULT YELLOW Lights when one of the detection zones has a fault
ZONE 1-6 TEST YELLOW Lights when one of the detection zones is in test mode
ZONE 1-6 DISABLED YELLOW Lights when one of the detection zones is in disablement mode
1
ST
STAGE SNDR ACTIVE RED Lights when the first stage sounder is on
1
ST
STAGE SNDR FAULT YELLOW Lights when the first stage sounder has a wiring fault
1
ST
STAGE SNDR TEST YELLOW Lights when the first stage sounder is in test mode
1
ST
STAGE SNDR DISABLED YELLOW Lights when the first stage sounder is disabled
2
ND
STAGE SNDR ACTIVE RED Lights when the second stage sounder is on
2
ND
STAGE SNDR FAULT YELLOW Lights when the second stage sounder has a wiring fault
2
ND
STAGE SNDR TEST YELLOW Lights when the second stage sounder is in test mode
2
ND
STAGE SNDR DISABLED YELLOW Lights when the second stage sounder is disabled
BOTTLE OUTPUT ACTIVE RED Lights when the bottle output is on
BOTTLE OUTPUT FAULT YELLOW Lights when the bottle output has a wiring fault
BOTTLE OUTPUT DISABLED YELLOW Lights when the bottle output is disabled
1
ST
STAGE RELAY ACTIVE RED Lights when the first stage relay is on
1
ST
STAGE RELAY TEST YELLOW Lights when the first stage relay is in test mode
1
ST
STAGE RELAY DISABLED YELLOW Lights when the first stage relay is disabled
2
ND
STAGE RELAY ACTIVE RED Lights when the second stage relay is on
2
ND
STAGE RELAY TEST YELLOW Lights when the second stage relay is in test mode
2
ND
STAGE RELAY DISABLED YELLOW Lights when the second stage relay is disabled
MAN.L RELEASE INPUT ACTIVE RED A manual release call point connected to the remote input has been activated
MAN. RELEASE INPUT FAULT YELLOW Fault in wiring to Manual release call point
MAN. RELEASE INPUT DISABLED YELLOW Manual release call point circuit is disabled
GAS FIRED INPUT ACTIVE RED The panel has received a signal from the cylinder to say the gas has been released.
GAS FIRED INPUT FAULT YELLOW There is a wiring fault to the bottle`s sensor
EMERG. HOLD INPUT ACTIVE YELLOW The emergency hold input has been activated
EMERG. HOLD INPUT FAULT YELLOW Fault in wiring to Emergency hold switch
EMERG. ABORT INPUT ACTIVE YELLOW The emergency abort input has been activated
EMERG. ABORT INPUT FAULT YELLOW Fault in wiring to Emergency abort switch
AUTO/MANUAL INPUT ACTIVE YELLOW The panel has been set to manual mode by a remote input
AUTO/MANUAL INPUT FAULT YELLOW Fault in wiring to Auto / Manual switch
PRESS. SWITCH INPUT ACTIVE YELLOW The bottle`s pressure switch output has been activated
PRESS. SWITCH INPUT FAULT YELLOW Fault in wiring to bottle`s pressure switch
BOTTLE SCALES INPUT ACTIVE YELLOW The bottle`s scales switch has been activated
BOTTLE SCALES INPUT FAULT YELLOW Fault in wiring to bottle`s scales switch
ACCESS LEVEL 3 YELLOW Access level 3 selected
GAS RELEASE COUNTER YELLOW Gas release counter is being displayed on 3 digit display
RELEASE DURATION TIME YELLOW Release duration time is being displayed on 3 digit display
RESET INHIBIT TIME YELLOW Reset inhibit time is being displayed on 3 digit display