background image

Author: RK 

Version: 2.3 

Revision: 1.4 

Revision Date: February 2022 

 

IMPORTANT:  

There must be adequate space to reach the controls situated at the 

back of the appliance. 

NOTE:           

Any  gas  supply  cylinder  should  have  at  least  250mm  clearance  if 

placed behind the appliance. 

 

GAS CONNECTION:

 

 

The  appliance  inlet  is  to  the  8mm  plain  straight  tube,  allowing  connection  by 

means  of   a  gas-tight  compression  fitting   to  comply  with  both  EC   and  local 
regulations.  The  freezer  is  suitable  for  connection  to  butane/propane  mixtures 
(LPG)  at  2.8-3.0 kPa  and  to  propane  at  3.7  kPa.  Means  must  be  provided  to  turn 
off the gas supply. If the supply is common to other appliances a separate tap must 
be fitted for the freezer line. 

WARNING

:

ENSURE   THAT   THE   GAS   SUPPLY   HOSE   IS   NOT   IN

 

CONTACT WITH OR NEAR THE BURNER BOX

 

 

GAS-PRESSURE REGULATOR

 

 

This appliance requires an operating pressure of 2.8 kPa at the appliance. A 

suitable LPG regulator that complies with the requirements of SANS 1237 

must be installed. 

 

OPERATING INSTRUCTIONS FOR FREEZER

 

 

It  is important to read through these instructions carefully before beginning  to use 

this appliance. 

Retain these instructions for future reference. 

 

LP. GAS OPERATION:

 

 

After  initial  installation,  after  changing  gas  cylinder,  after  servicing,  etc.,  the  gas 
pipes  may contain  some air,  which  should  be  allowed  to  escape by briefly pressing 
on  the  safety  valve  knob  (A)  See  page  4.  This  will  ensure  that  the  flame  lights 
quickly. Do not press knob A for more than 5 seconds – see Users note. 

 

BURN-BACK (FIRE IN BURNER TUBE OR CHAMBER) 
(REFER PAGE 4 – TO START G AS OPERATION)

 

In the event of a burn-back, where the flame burns back to the jet, immediately turn 

off the gas supply at the control valve on the gas bottle or gas supply. After 

ensuring the flame is extinguished, re-open and re-light the appliance in the normal 
manner. Should the appliance again burn back, close the control valve and call a 
service technician. Do not use the appliance again until the service technician has 
declared that it is safe to do so. 

 

W ARNING

 

This  appliance  consumes  air  (oxygen).  Provide  ample  ventilation  especially  when 
sleeping.  To  avoid  endangering  your  life  do  not  use  this  freezer  in  unventilated 
structures.   Provide  additional  ventilation for  any additional fuel  burning  appliances 
and  additional  occupants.    Always  ensure  nothing  is  covering  or  blocking  the flue 
(chimney).

Summary of Contents for GF180IP













Reviews: