background image

 

Page 8 

 

Juggler 73-404-00 Issue 1 

Sequences 

 

Introduction 

A sequence is a series of up to 99 states which are stored in the desk and can be played 
back sequentially. Up to 12 sequences may be programmed and stored on the Juggler.  

Only  one  programmed  sequence  may  be  played  back  at  a  time.  A  sequence  can  be 
played back manually or automatically. Transitions between the steps can be snap or fade.  

The SEQUENCE MASTER fader controls the maximum output level of the sequence. 

The LED in the SEQUENCE button indicates the ‘mode’ as follows: 

Off = No Sequence Running 

On = Program Mode 

Flashing = Playback Mode 

The seven segment display shows the selected step number in the sequence. When the 
SHIFT key is held down the seven segment display shows the sequence number. The UP 
and DOWN  buttons are used to change the selected step or sequence number.  

If no sequence is being output the seven segment display shows “—“ as an indication that 
the desk is powered (there is no separate power LED on the desk). 

 

Programming Sequences 

To enter Program Mode – hold down the SEQUENCE button for about two seconds. The 
LED in the SEQUENCE button comes on. 

Hold  down  the  SHIFT  button  and  use  the  UP  and  DOWN  buttons  to  select  the  required 
sequence  number  (1  –  12).  Release  the  SHIFT  button.  The  seven  segment  display  now 
indicates the step number. 

Use the UP and DOWN buttons to select the required step number ( 1 – 99). 

Use the PRESET A and PRESET B faders to set up the required output levels for the step. 

Press  the  SEQUENCE  button  to  program  the  selected  step.  The  selected  step  will 
automatically increment to the next step and the LED in the SEQUENCE button will flash 
momentarily to indicate that the step was programmed. 

Repeat the above procedure for each step to be programmed in the sequence. 

Set  the  SEQUENCE  SPEED  and  FADE  TIME  controls  to  the  required  values  for  the 
sequence. 

To exit Program Mode hold down the SEQUENCE button for about two seconds.  

The desk returns to Playback Mode and the last selected sequence is started and output. 

 

Summary of Contents for Juggler

















Reviews: