background image

Important Safety Notice

3

WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

CAUTION

To reduce risk of fire and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings,

attics, crawl spaces or garages.

OPERATION

Always leave safety grilles and filters in place. Without these components, operating blowers could catch onto hair, fingers 

and loose clothing.
The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation, 

maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to 

negligence and the warranty of the unit automatically expires due to improper maintenance.

*NOTE: Please check www.zephyronline.com for revisions before doing any custom work.

ELECTRICAL REQUIREMENTS

Important:

Observe all governing codes and ordinances.
It is the customer’s responsibility:

-  To contact a qualified electrical installer.

-  To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 

latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and 

all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the 

ground path is adequate.
Do not ground to a gas pipe.

Check with a qualified electrician if you are not sure the range hood is properly grounded.

Do not have a fuse in the neutral or ground circuit.

*National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269

 

** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575
This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit 

protected by a 15 or 20 ampere circuit breaker or time delay fuse.  Wiring must be 2 wire with ground.  Please also refer to 

Electrical Diagram on product.

A cable locking connector (not supplied) might also be required by local codes.  Check with local requirements, purchase 

and install appropriate connector if necessary.

INTENDED FOR OUTDOOR COVERED PATIO OR LANAI AREA. 

SUITABLE FOR USE IN DAMP LOCATIONS WHEN INSTALLED IN A 

GFCI PROTECTED BRANCH-CIRCUIT.

Cancer and Reproductive Harm - www.P65Warnings.ca.gov

WARNING

Prop. 65 Warning for California Residents

Summary of Contents for AK9834AS





















Reviews: