manualshive.com logo in svg

Zenoah PSZ2600, Owner'S Manual

Share
Download
Zenoah PSZ2600 Owner'S Manual Download Page 12

GB-12

PSZ2600

9. Maintenance

TIGHTENING TORQUE:

9.8 - 11.8 N.m.
(1 - 1.2 kg.m.)

 

 WARNING

•

Make sure that the engine has stopped and is cool be-
fore performing any service to the machine. Contact with
moving cutting head or hot muffler may result in a per-
sonal injury.

AIR FILTER

• The air filter, if clogged, will reduce the engine performance.

Check and clean the filter element in warm, soapy water as
required. Dry completely before installing. If the element is
broken or shrunk, replace with a new one.

(1)

(1) Air filter

FUEL FILTER

• When the engine runs short of fuel supply, check the fuel

cap and the fuel filter for blockage.

(1)

(1) Fuel filter

SPARK PLUG

• Starting failure and misfiring are often caused by a fouled

spark plug. Clean the spark plug and check that the plug
gap is in the correct range. For a replacement plug, use the
correct type specified by ZENOAH.

•

REPLACEMENT PLUG IS A NGK CMR7A.

 IMPORTANT

•

Note that using any spark plug other than those designated
may result in the engine failing to operate properly or in the
engine becoming overheated and damaged.

•

To install the spark plug, first turn the plug until it is finger
tight, then tighten it a quarter turn more with a socket wrench.

MUFFLER

 WARNING

•

Inspect periodically, the muffler for loose fasteners, any
damage or corrosion. If any sign of exhaust leakage is
found, stop using the machine and have it repaired im-
mediately in the repair specialty store.

•

Note that failing to do so may result in the engine catch-
ing on fire.

Every Every Every

25

50

100

System/components

Procedure

Before

hours hours hours

 Note

use

after

after

after

fuel leaks, fuel spillage

wipe out

✔

fuel tank, air filter, fuel filter

inspect/clean

✔

✔

replace, if necessary

see adjusting

replace carburetor

idle speed adjuster

idling speed (p. 10)

✔

if necessary

clean and readjust

GAP: 0.65 mm

spark plug

plug gap

✔

replace, if necessary

intake air cooling vent

clean

✔

throttle trigger, stop switch

check operation

✔

transmission

grease

✔

screws/nuts/bolts

tighten/replace

✔

✔

not adjusting screws

oiling port

clean

✔

✔

guide bar

clean

✔

sprocket

inspect/replace

✔

saw chain

inspect/sharp

✔

ENGINE

SHAFT

CUTTING UNIT

0.65 mm

Summary of Contents for PSZ2600

















Reviews:

No comments

Brands by name

Popular brands

Load more brands