![background image](http://html2.mh-extra.com/html/zenoah/gz4350/gz4350_operators-manual_3482255026.webp)
First adjust the L-jet, followed by the idiling T-screw and
finally the H-jet.
CAUTION: Do not attempt to adjust the L-
and H-jets beyong either stop as this could
cause damage.
1. Make sure that the air filter is clean and the cylinder
cover is fitted before you make any adjustments.
CAUTION: If you adjust the carburetor
while a dirty air filter is in use this will
result in a leaner mixture next time the
filter is cleaned. This can give rise to
serious engine damage.
2. Start the product and let it warm up for 10 minutes.
See instructions under heading
13
3. Place the product on a flat surface so that the guide
bar points away from you and so that the guide bar
and saw chain do not come in contact with the
surface or other objects.
4. Turn the low speed L-jet clockwise until it stops.
5. If the engine accelerates poorly or idles unevenly,
turn the low speed L-jet anti-clockwise until you
achieve good acceleration and idling.
6. If it is necessary to re-adjust, turn the T-screw
clockwise until while the engine is running until the
saw chain starts to rotate.
7. Turn anti-clockwise until the saw chain stops.
Note: When the idle speed is correctly adjusted the
engine should run smoothly in every position and the
engine speed should be safely below the speed at
which the saw chain starts to rotate.
WARNING: Contact your servicing
dealer if the idle speed setting can not
be adjusted so that the saw chain stops
at idle. Do not use the product until it has
been properly adjusted or repaired.
At the factory the engine is adjusted at sea level. When
working at a high altitude or in different weather
conditions, temperatures and atmospheric humidity, it
may be necessary to make minor adjustments to the
high speed H-jet. When test run at the factory, the high
speed H-jet is set so that the engine satisfies the
applicable legal requirements at the same time as it
achieves maximum performance. The high speed H-jet
of the carburetor is then locked using a limiter cap in the
fully screwed out position. The limiter cap limits the
potential to adjust the high speed H-jet to at most 1/2
turn.
CAUTION: If the high speed H-jet is screwed
in too far, it may damage the piston/cylinder.
When the carburetor is correctly adjusted the product
accelerates without hesitation and 4-cycles a little at
maximum speed. It is also important that the saw chain
does not rotate at idle. If the L-jet is set too lean it may
cause problems when you start the product, as well as
poor acceleration. If the H-jet is set too lean the product
will have less power, poor acceleration and could suffer
damage to the engine.
Examination, maintenance and service
of the product's safety equipment
Note: All service and repair work on the product
demands special training, especially maintenance work
regarding the safety devices on the product. If your
product fails any of the checks described below we
recommend you to bring your product to your servicing
dealer.
To do a check of the brake band
1. Brush off any wood dust, resin and dirt from the
chain brake and clutch drum. Dirt and wear can
impair operation of the brake.
2. Do a check of the brake band. The brake band must
be at least 0,6 mm (0.024 inch) thick at its thinnest
point.
To do a check of the front hand guard
Regularly carry out a check of the front hand guard and
the inertia brake release.
1. Do a visible check to make sure the front hand guard
is not damaged and that there are no visible defects
such as cracks.
26
320 - 005 - 27.09.2017
Summary of Contents for GZ4350
