background image

GZ3500T

GB-2

Read operator's instruction
book before operating this
machine.

Wear head, eye and ear
protection.

Use the chain saw
with two hands.

Warning! Danger of
kickback.

Read, understand and
follow all warnings.

This saw is for trained tree
service operators only.

Use appropriate protections
for foot-leg and hand-arm.

Never touch hot surface.

APPROVAL NUMBER OF CE EXHAUST EMISSION REGULATION (2002/88/EC)

e13

*

97/68SH2G3

*

2002/88

*

0432

*

00

WARNING!!!

RISK OF DAMAGING HEARING

Wear head, eye and ear protection.

WARNINGS IN THE MANUAL

WARNING

This mark indicates instructions, which must be followed in order to prevent accidents, which could lead to serious
bodily injury or death.

IMPORTANT

This mark indicates instructions, which must be followed, or it leads to mechanical failure, breakdown, or damage.

NOTE

This mark indicates hints or directions useful in the use of the product.

SYMBOLS IN THE OPERATOR’S MANUAL

SAFETY FIRST

Instructions contained in warnings within this manual marked with a 

 symbol concern critical points which must be

taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all
such instructions carefully and follow them without fail.

Front handle Rear handle

SOUND LEVEL

VIBRATION LEVEL

ISO 22868

LwA

ISO 22867

MODEL

GZ3500T

LpA

Front handle Rear handle

A(8)

35.2 cm

3

98.3 dB(A)

112 dB(A)

6.7 m/s

2

6.1 m/s

2

3.7 m/s

2

3.3 m/s

2

2002/44/EC

DISPLACEMENT

Summary of Contents for GZ3500T



















Reviews: