background image

GB-16

G6200

Limited warranty

Should any failure occur on the product under normal 
operating  conditions  within  the  applicable  warranty 
period, the failed part will be replaced or repaired free 

of charge by a ZENOAH authorized dealer.

WARRANTY PERIOD:

 Six (6) months after purchased 

by end-user subject to 12 months from produced month. 
(30 days If used for rental purpose)

THE  PURCHASER  SHALL  BEAR  COSTS  OF  TRANS-

PORTING  THE  UNIT  TO  AND  FROM  THE  ZENOAH 

DEALER. 

THE  PURCHASER  SHALL  NOT  BE  CHARGED  FOR 
DIAGNOSTIC LABOR WHICH LEADS TO THE DETER-
MINATION THAT A WARRANTED PART IS DEFECTIVE, 
IF THE DIAGNOSTIC WORK IS PER FORMED AT THE 

ZENOAH DEALER.

THE PURCHASER OR OWNER IS RESPONSIBLE FOR 
THE  PERFORMANCE  OF  THE  REQUIRED  MAINTE-
NANCE AS DEFINED BY THE MANUFACTURER IN THE 
OWNER/OPERATOR MANUAL.

ANY WARRANTED PART WHICH IS NOT SCHEDULED 
FOR REPLACEMENT AS REQUIRED MAINTENANCE, 
OR  WHICH  IS  SCHEDULED  ONLY  FOR  REGULAR 
INSPECTION  TO  THE  EFFECT  OF  REPAIR  OR  “RE-
PLACE AS NECESSARY” SHALL BE WARRANTED FOR 
THE  WARRANTY  PERIOD.  ANY  WARRANTED  PART 
WHICH IS SCHEDULED FOR REPLACEMENT AS RE-
QUIRED MAINTENANCE SHALL BE WARRANTED FOR 
THE PERIOD OF TIME UP TO THE FIRST SCHEDULED 
REPLACEMENT POINT FOR THE PART.

ANY REPLACEMENT PART THAT IS EQUIVALENT IN 
PERFORMANCE AND DULABILITY MAY BE USED IN 
NON-WARRANTY MAINTENANCE OR REPAIRS, AND 

SHALL NOT REDUCE THE WARRANTY OBLIGATION 
OF THE COMPANY.

THE COMPANY IS LIABLE FOR DAMAGES TO OTHER 
ENGINE COMPONENTS CAUSED BY THE FAILURE OF 
A WARRANTED PART STILL UNDER WARRANTY.

THE WARRANTY DOES NOT APPLY TO

 THOSE UNITS 

WHICH HAVE BEEN DAMAGED BY NEGLIGENCE OF 
INSTRUCTION  LISTED  IN  THE  OWNER/OPERATOR 
MANUAL FOR PROPER USE AND MAINTENANCE OF 
THE UNITS ACCIDENT MISHANDLING, ALTERATION, 
ABUSE,  IMPROPER  LUBRICATION,  USE  OF  ANY 
PARTS  OR  ACCESSORIES  OTHER  THAN  THOSE 
SPECIFIED BY THE COMPANY, OR OTHER CAUSES 
BEYOND THE COMPANY'S CONTROL.

THIS WARRANTY DOES NOT COVER

 THOSE PARTS 

REPLACED  BY  NORMAL  WEAR  OR  HARMLESS 
CHANGES IN THEIR APPEARANCE.

THERE ARE NO OTHER EXPRESS WARRANTIES.

ANY IMPLIED WARRANTY

 is limited to the duration of 

the limited warranty. Otherwise, this limited warranty is 
in lieu of all other expressed or implied warranties, in-
cluding any warranty of 

FITNESS FOR A PARTICULAR 

PURPOSE OR USE

 and any implied warranty 

MER-

CHANTABILITY

 otherwise applicable to this product.

LIABILITIES FOR INCIDENTAL OR CONSEQUENTIAL 
DAMAGE UNDER ANY AND ALL WARRANTIES ARE 
EXCLUDED.

IF  YOU  NEED  TO  OBTAIN  MORE  INFORMATION, 
PLEASE CALL YOUR NEAREST SERVICE CENTER, OR 

CHECK  PLEASE  ZENOAH  WEB  SITE 

http://www.ze-

noah.net

Summary of Contents for G6200

















Reviews: