Zenoah EHT603D Page 16 Owner'S Manual Download | Manualshive

Page: 16 / 20

background image

16

English

6. MAINTENANCE

F11

F12

3. Check if the safety lock returns to

its original position when you
release your hand from safety
lock.

If you find any defects at the checks
above, contact your nearest servicing
dealer for repair.

■

ANTI-VIBRATION SYSTEM (F11)

The deformed or damaged anti-
vibration system may cause of the
breakages like getting rickety or
falling off of engine and/or blade.

• [eHT753S] Check periodically if

the rubber cushions are not
deformed or damaged.

• [eHT603D] Check periodically if

the springs are not deformed or
damaged.

■

AIR CLEANER (F12)

Release the air cleaner cover and
remove dusts. In case the element is
dirty, carefully wash it with warm
water containing neutral detergent.
Completely dry before refitting the
element. If the element is deformed
or damaged, replace it with new one.

(1) Element
(2) Filter
(3) Air cleaner cover

Clogged air cleaner spoils engine
performance. Also, operation with no
element or with deformed or
damaged element causes irregular
wear outs of the engine mechanism.

IMPORTANT

WARNING

«
...
14
15
16
17
18
...
»

Summary of Contents for EHT603D





















Reviews:

No comments

Related manuals for EHT603D

Brand: CO/Tech Pages: 60

Brand: Nakayama Pages: 28

Brand: Pattfield Ergo Tools Pages: 86

POWERplus POWXG8010LI

Brand: VARO Pages: 12

sunjoe 24V-ST14B-CT

Brand: SNOWJOE Pages: 60

Brand: Okay Pages: 40

Brand: Okay Pages: 60

Brand: PLP Pages: 28

Brand: Kärcher Pages: 212

Brand: Wolf Garten Pages: 236

Brand: Ryobi Pages: 16

Brand: Ryobi Pages: 34

Brand: Ryobi Pages: 62

Brand: sunjoe Pages: 20

Brand: Worcraft PROFESSIONAL Pages: 54

Brand: HENX Pages: 13

Brand: Jonsered Pages: 24

Brand: Jonsered Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands