manualshive.com logo in svg

Zenoah BKZ4505DL, Owner'S Manual

Share
Download
Zenoah BKZ4505DL Owner'S Manual Download Page 13

GB-13

G

B

BKZ4505DL / BKZ5010DL

METAL BLADE USAGE

1. Check the bolt to fasten the blade and be sure the

bolt has no fault, and no abrasion.

2. Be sure that the blade and the holder have been fas-

tened according to instruction and the blade turns
smoothly without abnormal noise.

 WARNING

• The rotating parts fastened incorrectly may cause

serious accident to the operator.

• Make sure that the blade is not bent, warped,

cracked, broken or damaged.

• If you find any error to the blade, discard it and

change new one which is certified by ZENOAH.

• By using the harness, hang the unit on your right side.

Adjust the harness length so that the cutting head
may become parallel to the ground.

 WARNING

• Make sure to use harness and cutting attachment

guard. If not, it is vary dangerous when you slip or
lose your balance.

• Be sure to use genuine parts made of Zenoah for

blades. In particular, never use special blades such
as shredder blades. If you use a special blade, the
unit may fail.

• Do not use the Zenoah blade 848-JLO-92A2 or the

blade whose thickness is more than 2mm.

ADJUSTING THROTTLE CABLE

• The normal play is 1 or 2 mm when measured at the

carburetor side end. Readjust with the cable adjuster
as required and tighten the screw up.

(1)

(3)

(2)

ADJUSTING IDLING SPEED

1. When the engine tends to stop frequently at idling

mode, turn the adjusting screw clockwise.

2. When the cutting head keeps rotating after releasing

the trigger, turn the adjusting screw counter-clockwise.

(1)

 NOTE

• Warm up the engine before adjusting the idling speed.

PUTTING ON THE UNIT

1. Start the engine and warm it up.
2. As holding the front handle with your right hand, put

on the unit on your left shoulder.

3. After passing the front handle to your left hand, put

the right harness on your shoulder.

4. Adjust the harness length to your comfortable posi-

tion.

5. Connect the waist harness and the front middle har-

ness.

6. Adjust the harness length to your comfortable posi-

tion.

      

CUTTER APPLICATION CHART

•   Replace by a suitable recommended cutting attach-

ment according to the object to be cut.

•  When replacing blade always be sure to use products

which have been certified by ZENOAH.

 WARNING

•   When sharpening, removing, or reattaching the blade,

be sure to wear thick, sturdy gloves and use only
proper tools and equipment to prevent injury.

8. Operation

(1) Cable adjuster
(2) 0.04in (1~2mm)
(3) Screw

(1) Idle speed adjuster
     (cross screw)

Summary of Contents for BKZ4505DL



















Reviews:

No comments

Brands by name

Popular brands

Load more brands