Zenoah BCZ4505DW Owner'S Manual Download Page 19

GB-19

G

B

BCZ4505DW / BCZ4505CL / BCZ5010DL / BCZ5010DW / BCZ5010CL

11. Troubleshooting guide

Case 1. Starting failure

CHECK

PROBABLE CAUSES

ACTION

fuel tank

incorrect fuel

drain it and use correct fuel

fuel filter

fuel filter is clogged

clean

carburetor adjustment screw

out of normal range

adjust to normal range

sparking (no spark)

spark plug is fouled/wet

clean/dry

plug gap is incorrect

correct (GAP: 0.6 ~ 0.7 mm)

spark plug

disconnected

retighten

Case 2. Engine starts but does not keep running/hard re-starting

CHECK

PROBABLE CAUSES

ACTION

fuel tank

incorrect fuel or staled fuel

drain it and use correct fuel

carburetor adjustment screw

out of normal range

adjust to normal range

muffler, cylinder (exhaust port)

carbon is built-up

consult with the repair specialty store

air cleaner

clogged with dust

air blow or wash

cylinder fin, fan cover

clogged with dust

consult with the repair specialty store

When your unit seems to need further service, please consult with our ZENOAH service shop in your area.

12. Disposal

When you dispose of the machine, do  not disas-
semble the machine.

When you dispose of the machine, fuel, oil, be sure
to follow your local regulations.

Limited warranty

Should any failure occur on the product under normal oper-
ating conditions within the applicable warranty period, the
failed part will be replaced or repaired free of charge by a
ZENOAH authorized dealer.

WARRANTY PERIOD:

 1 year (6 months if used profession-

ally, and 30 days if used for rental purpose) from the date of
initial purchase.

THE PURCHASER SHALL BEAR COSTS OF TRANSPORTING
THE UNIT TO AND FROM THE ZENOAH DEALER.

THE PURCHASER SHALL NOT BE CHARGED FOR DIAG-
NOSTIC LABOR WHICH LEADS TO THE DETERMINATION
THAT A WARRANTED PART IS DEFECTIVE, IF THE DIAG-
NOSTIC WORK IS PERFORMED AT THE ZENOAH DEALER.

THE PURCHASER OR OWNER IS RESPONSIBLE FOR THE
PERFORMANCE OF THE REQUIRED MAINTENANCE AS
DEFINED BY THE MANUFACTURER IN THE OWNER/OPERA-
TOR MANUAL.

ANY WARRANTED PART WHICH IS NOT SCHEDULED FOR
REPLACEMENT AS REQUIRED MAINTENANCE, OR WHICH
IS SCHEDULED ONLY FOR REGULAR INSPECTION TO THE
EFFECT OF REPAIR OR “REPLACE AS NECESSARY” SHALL
BE WARRANTED FOR THE WARRANTY PERIOD. ANY WAR-
RANTED PART WHICH IS SCHEDULED FOR REPLACEMENT
AS REQUIRED MAINTENANCE SHALL BE WARRANTED FOR
THE PERIOD OF TIME UP TO THE FIRST SCHEDULED RE-
PLACEMENT POINT FOR THE PART.

ANY REPLACEMENT PART THAT IS EQUIVALENT IN PER-
FORMANCE AND DULABILITY MAY BE USED IN NON-WAR-
RANTY MAINTENANCE OR REPAIRS, AND SHALL NOT RE-
DUCE THE WARRANTY OBLIGATION OF THE COMPANY.

THE COMPANY IS LIABLE FOR DAMAGES TO OTHER EN-
GINE COMPONENTS CAUSED BY THE FAILURE OF A WAR-
RANTED PART STILL UNDER WARRANTY.

THE WARRANTY DOES NOT APPLY TO

 THOSE UNITS

WHICH HAVE BEEN DAMAGED BY NEGLIGENCE OF IN-
STRUCTION LISTED IN THE OWNER/OPERATOR MANUAL
FOR PROPER USE AND MAINTENANCE OF THE UNITS
ACCIDENT MISHANDLING, ALTERATION, ABUSE, IM-
PROPER LUBRICATION, USE OF ANY PARTS OR ACCES-
SORIES OTHER THAN THOSE SPECIFIED BY THE COM-
PANY, OR OTHER CAUSES BEYOND THE COMPANY’S CON-
TROL.

THIS WARRANTY DOES NOT COVER

 THOSE PARTS RE-

PLACED BY NORMAL WEAR OR HARMLESS CHANGES IN
THEIR APPEARANCE.

THERE ARE NO OTHER EXPRESS WARRANTIES.

IMPLIED WARRANTIES

  INCLUDING THOSE OF MER-

CHANTABILITY AND FITNESS FOR A PARTICULAR PUR-
POSE 

ARE LIMITED

 TO TWO (2) YEARS OF HOME USE

[ONE (1) YEAR FOR ANY OTHER USE] FROM THE ORIGI-
NAL DELIVERY DATE.

LIABILITIES FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGE UNDER ANY AND ALL WARRANTIES ARE EX-
CLUDED.

IF YOU NEED TO OBTAIN MORE INFORMATION, PLEASE
C A L L   Y O U R   N E A R E S T   S E R V I C E   C E N T E R ,
O R   C H E C K   P L E A S E   Z E N O A H   W E B   S I T E
http://www.zenoah.net

Summary of Contents for BCZ4505DW




















Reviews: