background image

6

For safe operation and maintenance,
symbols are carved in relief on the machine.
According to these indications, please be
careful not to take a mistake.

(a) The port to refuel the "MIX GASOLINE" 

Position:

FUEL TANK CAP

(b) The direction to close the choke

Position:

AIR CLEANER COVER

(c) The direction to open the choke

Position:

AIR CLEANER COVER

4. Symbols on the machine

IMPORTANT 

ENGINE INFORMATION

THIS ENGINE MEETS U.S. EPA PH2 

  AND 2001 CALIFORNIA EMISSION

       REGULATIONS FOR SI SORE’s 

    COMPLIANCE PERIOD : CATEGORYA:

ENGINE FAMILY : 2KZXS.0236JK ; EM
ENGINE DISPLACEMENT : 23.6cc

REFER TO OWNER’S MANUAL FOR MAINTE-

NANCE SPECIFICATIONS AND ADJUSTMENTS.

            

Ce moteur est conformc aux normcs U.S. 

       EPA PH2 et 2001 ainsi qu’aux autres dispositions 
   ultérieures de la réglementation concernant la pollution 
  de l’air pour les petits moteurs tout-terrain avec une 
 période de accordable : CATEGORYA.

Type de moteur : 

2KZXS.0236JK

 ; EM

Cylindrée du moteur : 23,6cc

Se référer au Manuel de l’utilisateur pour les 
spécifications d’entretien et les réglages.

INFORMATION IMPORTANTE 
CONCERNANT LE MOTEUR

Summary of Contents for BCZ2400S





































Reviews: