background image

3

B: BC3500LE/WE/BC4500WE/BC530WE

Using attached 4 socket screws, secure the
connection firmly with equal force. 

D: BC3500WE/BC4500WE/BC530WE
1. Remove the upper cap from the bracket. 
2. Loosen the 4 bolts on the clamp and insert the

handles equally.  Retighten the bolts. 

3. Put the handle assembly into the bracket and put

the upper cap over it. Tighten the cap securely.

PROTECTOR 

Wrap the protector around the outer pipe as
shown in the figure, and fasten the magic
fastener. 

BLADE GUARD 

Attach the guard
to the clamp on
the outer pipe just
touching the
gearcase. Fix it
with 2 bolts. 

Setup

BC2610WE
BC3500WE
BC4500WE

BC3500WE

BC4500WE

BC2310LE

BC2610LE

BC3500LE

HANDLE

A: BC2310LE/BC2610LE/BC3500LE

Put the handle onto the main pipe and fix it with 4
screws. 

CONNECTING SWITCH WIRES

Connect the switch wires between the
engine and the main unit.

BC530WE

B: BC530WE

BC530WE only remove the
screw(1) from the right
grip(2) and put the grip onto
the right handle. Align the
positioning holes and put
the screw through them.
Fasten the clamp(3). And
thencontinue to C.

BC530WE

BC530WE

CONNECTING THROTTLE WIRE

[EXCEPT BC530]

1. Remove the air cleaner cover.
2. Connect the end of the throttle wire to the joint on

the top of the carburetor.

1.

2.

• Gasoline is very flammable. Avoid smoking

or bringing any flame or sparks near fuel.
Make sure to stop the engine and allow it cool
before  refueling the unit. Select outdoor bare
ground for fueling and move at least 3m (10ft)
away from the fueling point before starting
the engine. 

WARNING

• The Zenoah engines are lubricated by oil

specially formulated for air-cooled 2-cycle
gasoline engine use. If Zenoah oil is not
available, use an anti-oxidant added quality oil
expressly labeled for air-cooled 2-cycle engine
use. (JASO FC GRADE OIL or ISO EGC
GRADE)

• Do not use BIA or TCW (2-stroke water-cooling

type) mixed oil.

• Exhaust emission are controlled by the

fundamental engine parameters and
components (eq., carburation, ignition timing
and port timing) without addition of any
major hardware or the introduction of an inert
material during combustion.

• These engines are certified to operate on

unleaded gasoline.

• Make sure to use gasoline with a minimum

octane number of 89 RON (USA/Canada: 87AL)

INSTALLING CUTTING HEAD 

1. While locking the gear shaft by inserting the

attached bar into the upper holder and the
gear box, loosen and remove the hexagon
bolt(left-handed)

2. Using the arbor bolt, screw in the cutting

head to the gear shaft over the holders.
Hand-tighten it securely.

4

Fuel

RECOMMENDED MIXING RATIO

GASOLINE 50:OIL 1

• If you use a gasoline of a lower octane value

than prescribed, there is a danger that the
engine temperature may rise and an engine
problem such as piston seizing may
consequently occur. 

• Unleaded gasoline is recommended to reduce

the contamination of the air for the sake of your
health and the environment.

• Poor quality gasolines or oils may damage

sealing rings, fuel lines or fuel tank of the
engine.

HOW TO MIX FUEL

1. Measure out the quantities of gasoline and oil to

be mixed.

2. Put some of the gasoline into a clean, approved

fuel container.

3. Pour in all of the oil and agitate well.
4. Pour In the rest of gasoline and agitate again for

at least one minute. As some oils may be
difficult to agitate depending on oil ingredients,
sufficient agitation is necessary for the engine to
last long. Be careful that, if the agitation is
insufficient, there is an increased danger of
early piston seizing due to abnormally lean
mixture.

5. Put a clear indication on the outside of the 

conta

container to avoid mixing up with gasoline or
other containers.

6. Indicate the contents on outside of container for

easy identification. 

FUELING THE UNIT

1. Untwist and remove the fuel cap. Rest the cap

on a dustless place.

2. Put fuel into the fuel tank to 80% of the full

capacity.

3. Fasten the fuel cap securely and wipe up any

fuel spillage around the unit.

1. Select bare ground for fueling.
2. Move at least 10feet (3meters) away from the

fueling point before starting the engine.

3. Stop the engine before refueling the unit. At

that time, be sure to sufficiently agitate the
mixed gasoline in the container.

FOR YOUR ENGINE LIFE, AVOID;
1. FUEL WITH NO OIL(RAW GASOLINE) – It will

cause severe damage to the internal engine
parts very quickly.

2. GASOHOL – It can cause deterioration of

rubber and/or plastic parts and disruption of
engine lubrication.

3. OIL FOR 4-CYCLE ENGINE USE – It can

cause spark plug  fouling, exhaust port blocking,
or piston ring sticking.

4. Mixed fuels which have been left unused for

a period of one month or more may clog the
carburetor and result in the engine failing to
operate properly.

5. In the case of storing the product for a long

period of time, clean the fuel tank after
rendering it empty. Next, activate the engine
and empty the carburetor of the composite fuel.

6. In the case of scrapping the used mixed oil

container, scrap it only at an authorized
repository site.

As lot details of quality assurance, read the
description in the section Limited Warranty
carefully. Moreover, normal wear and change in
product with no functional influence are not
covered by the warranty. Also, be careful that, if
the usage in the instruction manual is not
observed as to fhe mixed gasoline, etc. described
therein, if may not be covered by the warranty.

NOTE

WARNING

Pay attention to agitation.

C: BC2610WE
1. Loosen the 4 bolts on the upper cap and insert the

handles equally. Retighten the bolts.

2. Put the handle assembly into the bracket and put

the upper cap over it. Tighten the cap securely.

(Tightning torque: 4.9~7.8N.m.
(0.5~0.8kgm))

(1) Positioning hole
(2) Bolt (M5x10)
(3) Tightning bolt (M5x22)

BC2610WE

BC3500WE

BC4500WE

BC530WE

BC2310LE
BC2610LE/WE

ENGINE 

A: BC2310LE/BC2610LE/WE
1. Loosen the bolts temporarily attached to the clutch

housing.

2. Push the drivershaft toward the gearcase and

rotate it by hand to check that the driveshaft is
engaged with the gears.

3. Insert the shaft tube into the clutch housing until it

bottoms. When difficult to engage, twist the engine
slightly.

4. Align the positioning holes on the clutch housing

and the shaft tube and fit the bolt into the holes.
And fasten the tightning bolts by turns securely.

Summary of Contents for BC2310LE

Page 1: ... and hot surfaces 15 Warn the operator of the danger of blade thrust Kick back Blade thrust may occur when the spinning blade contacts a solid object in the critical area A dangerous reaction may occur causing the entire unit and operator to be thrust violently This reaction is called Kick back As a result the operator can lose control of the unit which can cause serious or fatal injury Kick back ...

Page 2: ...he quantities of gasoline and oil to be mixed 2 Put some of the gasoline into a clean approved fuel container 3 Pour in all of the oil and agitate well 4 Pour In the rest of gasoline and agitate again for at least one minute As some oils may be difficult to agitate depending on oil ingredients sufficient agitation is necessary for the engine to last long Be careful that if the agitation is insuffi...

Page 3: ...spool is capable for a line upto 6 m on the 4 head Avoid using a larger line as it may cut down the trimming performance 2 Pinch the slotted area on the both sides of the spool housing to unhook the bottom cap 3 Take out the spool and pull off the old line Put one end of new line through the spool holes and pull it until the length is equal between each part of the line 4 Wind up the line in the c...

Page 4: ...ndle type Loop Both Loop Both Throttle lever Trigger Type With Safety lock Standard cutter Nylon Harness type Single Double Quick release Yes Standard accessories Goggle Tool kit Owner s manual Specifications are subject to change without notice Specifications MAINTENANCE BEFORE STORAGE Old fuel left in the carburetor may cause starting failure When a series of operation finished make sure to empt...

Reviews: