Zenith P42W34 Service Manual Download Page 19

- 19 -

5. Adjustment of White Balance

5-1. Required Equipment

Color analyzer (CA-100 or similar product)

5-2. Connection Diagram of Equipment for 

Measuring 

(Manual Adjustment)

5-3. Adjustment of White Balance

O

Operate the Zero-calibration of the CA-100, then apply the

sensor to the PDP display surface.

O

Manual adjustment is also possible with the following sequence.  

(1) Select WHITE PATTERN of HEAT RUN mode by pressing

POWER ON KEY on the Adjustment R/C, then operate the
HEAT RUN for at least 15 minutes.

(2) Supply 216Gray, 50% size length and breadth signal to RGB

input. (Refer to Fig 2)

(3) W/B adjustment must be adjusted only High Light and then

save the adjustment value with 

Y

Key.

(4) To adjust High Light, apply sensor to 216 Gray Level (or 105-

115 Cd/m

2

) Pattern, press ADJ Key on Adjustment R/C and

press 

T

on Adjustment R/C to select R-L or G-L, press

VOL +, - Key(s) to adjustuntil color coordination becomes as
below.
X: 0.280±0.003,  Y: 0.290±0.003
Color temperature: 10,000°K±500°K

(5) Exit adjustment mode using 

Y

Key. 

6. DDC Data Input

6-1. Required Test Equipment

(1) A jig for adjusting PC, DDC. (PC serial to D-sub.

Connection equipment)

(2) S/W for writing DDC(EDID data write & read)
(3) D-Sub 15P cable, D-Sub to DVI Connector (DVI-D)

6-2. Setting of Device

6-3. Preparation for Adjustments

(1) Set devices as above and turn the PC, JIG on.
(2) Open S/W for writing DDC (EDID data write & read).

(operated in DOS mode)

6-4. Sequence of Adjustments

(1) DDC Data Input for Analog-RGB

1) Place the set on the table and turn the power on.
2) Connect PC Serial to D-sub 15P Cable of JIG for DDC

Adjustment to RGB terminal (D-Sub 15Pin). 

3) Open S/W for DDC record and select DDC Data for

Analog RGB in Model Menu.

4) Operate EDID Write command.
5) Operate EDID Read command and check whether

Check Sum is OK.

6) If Check Sum is NG, repeat 3) ~ 4).
7) If Check Sum is OK, DDC Data for Analog-RGB input is

completed.

(2) DDC Data input for Digital-RGB

1) Connect PC Serial to DVI Cable(DVI-D) of JIG for DDC

Adjustment to DVI terminal.

2) Operate S/W for DDC record and select DDC Data for

Digital RGB in Model Menu.

3) Operate EDID Write command.
4) Operate EDID Read command and check whether

Check Sum is OK.

5) If Check Sum is NG, repeat 3) ~ 4).
6) If Check Sum is OK, DDC Data for Digital-RGB input is

completed.

ADJUSTMENT INSTRUCTIONS

R-H  216

R-H  216
G-H  216

G-H  216

Window

VG828, MSPG-2100
 or MSTG-5200

High Light

216 Gray Level

<Fig 2>  Connection Diagram of Manual Adjustment

RGB Signal Input

PDP MONITOR

All manuals and user guides at all-guides.com

Summary of Contents for P42W34








































Reviews: