Zenitel VINGTOR STENTOFON EA1400 Installation And User Manual Download Page 10

Page: 10 / 17

EA1400/1600 Installation & User Manual

A100K11939



The mains power cable should be 3 x 1 mm

rated for 500 VAC.

WARNING

Do NOT disconnect the third (yellow/green) wire in the power plug. This wire grounds the amplifier’s

chassis to prevent a possible shock hazard. If an adapter is used to connect the plug to an ungrounded

outlet, make sure that the amplifier’s chassis is connected to the vessel’s central ground. In a rack

installation, the amplifier’s grounding point is connected to the rack frame.

3.5. Input Connection

The line inputs are balanced, accepting 0.5 -1.5 Vrms signal over 9 K ohm.

The signal source is connected between pin 1 and 2, and the wire shield is connected to pin 3.

If the signal source is unbalanced, connect the signal wire to pin 1 and the neutral wire to pin 2.

If two or more amplifiers are using the same audio signal, connect the SOURCE terminals on the first

amplifier to the corresponding IN terminals on the next amplifier.

The input levels must be adjusted individually (use VOLUME potentiometer on each amplifier unit).

Summary of Contents for VINGTOR STENTOFON EA1400


















Search results

Summary of Contents for VINGTOR STENTOFON EA1400

Reviews:

Related manuals for VINGTOR STENTOFON EA1400

Brands by name

Popular brands

Zenitel VINGTOR STENTOFON EA1400, Installation And User Manual

Search results

Summary of Contents for VINGTOR STENTOFON EA1400

Reviews:

Related manuals for VINGTOR STENTOFON EA1400

Brands by name

Popular brands