background image

 

Step 8 - PLUG-IN, TURN ON & VERIFY 
SETTINGS 

 

IMPORTANT 

ALL ELECTRICAL 
COMPONENTS MUST BE 
PLUGGED INTO GFCI / RCD 

NEVER PLUG ANYTHING NEAR YOUR TANK INTO 
THE WALL DIRECTLY. EVERYTHING SHOULD PLUG 
INTO A GFCI / RCD DEVICE. FAILURE TO DO SO 
MAY RESULT IN SERIOUS INJURY OR DEATH. 

  

1. Plug the Temperature Controller (#6), the Water Pump (#7a) and the 

UV Water Filter (#7b) ONLY into a GFCI Adapter (#9, if included) or a 
built-in GFCI / RCD outlet.  

2. Plug the two Heating Pads (#4a & #4b) into the Temperature 

Controller (#6)  

a. There are two available plugs from the Temperature Controller 

(#6), and one will have the Grounding Probe (#8) already 
pre-plugged into it 

b. Either Heating Pad plug can be used for either of the two 

available Temperature Controller plugs - operation is not 
affected by this selection 

3. Insert the Grounding Probe (#8) into the Tank through the access 

port  

4. Submerge the Grounding Probe (#8) and insert the tip into the built-in 

holder at the left rear of the Tank Interior 

5. Insert the Temperature Controller (#6) sensor into the Tank through 

the access port  

6. Submerge the Temperature Controller (#6) and insert the tip into the 

built-in holder at the left rear of the Tank Interior 

19 

Summary of Contents for Tank
























Reviews: