36
40Z011-001_v04
●
Do not place the appliance on or near open fire, hot
burner or heated oven.
●
It is not allowed to use charcoal or similar combustive
materials.
●
Before usage make sure that grease drip tray and grill
are properly assembled on the base.
●
Do not use your grill without grease drip tray
assembled.
●
Fill the grease drip tray with water up to max level, to
reduce smoke emission and make cleaning easier.
●
Do not move the grill pulling by supplying cord.
●
Do not let the supplying cord touch hot surfaces.
●
Use not sharp, the best wooden utensils to turn the
food, in order to avoid scratching non-sticking surface.
●
In case it is necessary to use sharp utensils and
knives, i.e. to cut something when grilling, at first
remove the product from the grill.
●
The appliance is not intended to be operated by means
of an external timer or separate remote-control system.
●
In order to avoid any risk posed by an unintentional
return to the initial state of thermal protection, the
equipment is not to be supplied via an external switch,
such as a programmable timer switch, or connected
to the circuit regularly enclosed and disabled by the
power supply.
●
It s not allowed to cover the heating plate with
aluminium foil, lid, etc, which can result with heat
accumulation and damage plastic parts and the layer.
●
Do not use aggressive detergents like cream, milk,
paste etc. to clean the casing. They can remove
graphic symbols such as: scales, marking, caution
signs, etc.
●
Do not wash the parts in dishwasher.
●
Dry thoroughly after cleaning. Make sure the appliance
is completely dry before thermostat assembling.
SUGGESTION
Information on the product and
suggestions for its use
●
The appliance is intended for household use, indoors
only.
●
The heating surface is coated with special non-stick
layer; therefore do not use sharp utensils for turning
grilled products. Use only soft wooden spatula.
●
In order to provide additional protection, it is
recommended to install the residual current device
(RCD) with nominal residual power not exceeding
30 mA. You should contact the professional electrician
in this concern.
●
While cooking some fatty dishes, it can be necessary
to empty the grease drip tray.
●
Apply the recommended temperature setting. You can
adjust the temperature during grilling if necessary.
Appliance elements
1
Grill base
2
Grease drip tray
3
Heating plate – grids
4
Lid
5
Thermostat with supplying cord
6
Pilot lamp
7
Heat-resistant handles
Technical parameters
Technical parameters are included at the name plate.
This device complies with Commission Regulation (EC)
no. 1275/2008 on eco-design requirements.
Assembling
Remove all stickers before first usage and
clean the appliance thoroughly (see: „Cleaning
and maintenance”).
●
Make sure hat the heating plate socket and thermostat
plug are dry.
1
Install the grease drip tray
(2)
at the base
(1)
.
2
Fill the grease drip tray with water up to max level, to
reduce smoke emission and make cleaning easier.
3
Assemble the heating plate
(3)
at the base.
4
Apply a small amount of oil on the heating plate before
usage and distribute it with paper towel.
5
Cover the grill with the lid
(4)
if necessary.
6
Insert the thermostat with supplying cord
(5)
in the
appliance socket.
7
Make sure that the thermostat knob is in “OFF” position.
8
Connect the supplying cord to the mains supply outlet.
Start-up
●
Set the thermostat
(5)
for desired temperature
(”I” to “V”).
“I” = the lowest temperature.
“V” = the highest temperature.
During warming up the pilot light
(6)
glows. When the
appliance reaches the set temperature, the light goes off and
the heater shall switch off. The grill heat up from time to time,
in order to keep the set temperature.
During first usage, the preserving materials
shall be burnt which can cause short emission
of unpleasant smell at the initial stage of
grilling.
It is not allowed to move the hot appliance
during operation! At first switch off and wait
until it cools down. Move with heat-resistant
handles only.
A
B