Zelmer Aquos 829, User Manual

Page: 57 / 67

60
B
Technical parameters
The type of the vacuum cleaner and the technical parameters
are indicated on the rating label. Mains protection 16 A.
Does not interfere with radio and TV reception.
Does not require grounding
.
ZELMER vacuum cleaners meet the requirements of the
applicable norms.
The appliance is in conformity with the requirements of the
directives:
Low voltage appliance (LVD) – 2006/95/EC. –
Electromagnetic compatibility (EMC) – 2004/108/EC. –
Noise level: 80 dB/A.
The appliance was marked by a CE sign on the rating label.
Appliance elements
1
ON/OFF button
2
Handle
3
Plug and cord
4
Cord rewind button
5
Power adjustment button , (type 829.0)
6
Power level indicator (type 829.0)
7
Accessory compartment cover
8
Motor fi lter (installed in the vacuum cleaner)
9
Foam fi lter II (installed in the vacuum cleaner)
10
HEPA outlet fi lter (installed in the vacuum cleaner)
11
Foam fi lter III (installed in the vacuum cleaner)
12
Anti-foam agent
13
Inlet fi lter (installed in the vacuum cleaner)
14
Foam fi lter I (installed in the vacuum cleaner)
15
Suction hose
16
Telescopic suction tube
17
SAFBAG dust bag
18
Crevice nozzle
19
Small brush
20
Small nozzle
21
Water pick up nozzle
22
Parquet brush “BNB”
Is used to clean and polish hard, scratch sensitive surfaces
such as wooden fl oors, fl oor panels, parquet, marble, tiles, etc.
Delicate and soft natural bristles ensure maximum vacuum
effectiveness and protects against scratching the cleaned
surface.
23
Combination brush. The vacuum cleaner is equipped
with only one type of combination brush (A or B)
A
Switchable combination brush
B
Combination brush with a small item separator
24
Turbo brush (type 829.0 ST)
25
Dry fi ltration module with SAFBAG dust bag
26
Water fi lter module ( fi ltration unit + partition)
Preparing the vacuum cleaner for
operation
1
Install the appropriate module in the vacuum cleaner (dry
fi ltration module with the SAFBAG dust bag or the water fi lter
module) ( see section C and E ).
2
Insert and snap the tank lid shut.
3
Insert the end of the suction hose to the vacuum cleaner
opening so that the hose interlock is in the protrusion of the
opening. A characteristic click indicates that the hose has
been properly installed.
4
Connect the other end of the hose (handle) with the
telescopic suction tube.
5
Adjust the length of the telescopic suction tube by sliding
the slider according to the arrow and pull out/pull the tube
together.
6
Assemble the appropriate nozzle or brush to the other
end of the suction tube.
7
You may assemble a basket for picking up small objects
in the combination brush with small item separator. In order
to do so remove the basket cover and insert the basket.
8
To clean hard surfaces – wooden fl oors, plastic fl oors,
ceramic tiles etc. pull out the brush by pressing the switch on
the nozzle according to the fi gure .
9
The vacuum cleaner is equipped with an accessory
compartment. The compartment is located in the front lid of
the appliance. To open/close the compartment lift/close the
lid and take out/ put away the desired nozzle.
10
Grab the plug (3) and pull the cord out of the vacuum
cleaner.
ATTENTION! While pulling out the cord pay attention
to the yellow stripe which signals the end of the
cord. Further attempts (pulling on cord) may result in
damaging the cord.
11
Plug in the appliance.
ATTENTION! Before operation, make sure that all
fi lters as well as the appropriate module are installed
in the appliance.
12
Switch on the vacuum cleaner by pressing the “on/off”
button (1) .
Vacuum cleaner functions
TRADITIONAL CLEANING WITH SAFBAG
DUST BAG
1
Press the “PRESS” button and remove the tank lid.
2
Remove the water fi lter module from the container
( fi ltration unit and partition).
ATTENTION! The water fi lter module/the dry fi ltration
module with the SAFBAG dust bag may only be
removed and inserted when the end of the hose is
removed from the vacuum cleaner opening.
A
C