Zeiss Crossbeam 350 Instruction Manual Download

Page: 88 / 126

6 Operation | 6.6 Working with Variable Pressure

ZEISS

6.5.9 Setting up the CL Detector

The CL detector is optionally available.

The CL detector collects visible or ultraviolet light and is especially useful for internal structural ex-
aminations of rocks, ceramics, and semiconductors.

Fig. 37: Zircon grains

The following settings are recommended for the CL detector:

EHT

Typical WD

5 kV – 30 kV

6–10 mm

(min. 4 mm)

1. In the Crossbeam SEM Control panel, select the Imaging tab.
2. From the

Signal A

drop-down list, select

3. Adjust the EHT and the working distance (WD) according to the suggestions in the table in

order to optimize the image.

6.6 Working with Variable Pressure

VP mode offers the possibility of analyzing and mapping non-conducting, strongly gassing or
moist specimens without any need for specimen preparation.

The partial pressure in the specimen chamber can be set in the range 0.1–0.6 mbar.

Instruction Manual ZEISS Crossbeam 350 | en-US | Rev. 3 | 349500-8111-000

Summary of Contents for Crossbeam 350































































































































Search results

Summary of Contents for Crossbeam 350

Reviews:

Related manuals for Crossbeam 350

Brands by name

Popular brands

Zeiss Crossbeam 350, Instruction Manual

Search results

Summary of Contents for Crossbeam 350

Reviews:

Related manuals for Crossbeam 350

Brands by name

Popular brands