background image

Step 1

Step 3

Step 2

‘LOCKED’

‘UNLOCKED’

Line Indicator

(1)

9

2.7        BMS Connectivity - CMEV.4eHT Only

2.7.1          The CMEV.4eHT unit can be connected to a BMS system that can provide a variable 0-10 Volt output that will be

                  used to control the fan operating speed, as shown within table 1.1 below:

2.7.2          

Removal of Fan Motor Assembly (See Figure 5)

                  WARNING: The CMEV.4eHT unit must be isolated from the mains supply before removing the fan motor 
                  assembly.

                      1) Remove external locking screw (1).
                      

CAUTION; Fan motor assembly is free to move after the next operation – in ceiling installations 

                      

please ensure the fan is manually supported during the following steps.

     

                      2) Rotate anti-clockwise, noting ‘LINE INDICATOR’ moving from the ‘LOCKED’ to ‘UNLOCKED’ position 
                      

(See Figure 5a). 

                      3) Fan motor assembly can now be lowered / lifted out of main fan housing.

2.7.3          Figure 5 – Removal of Fan Motor

                  Figure 5a – ‘LOCK’ & ‘UNLOCK’ Positions

Voltage

Speed Control

0V – 3.2V

Trickle

3.3V – 6.4V

Medium

6.5V – 10V

Boost

Table 1.1

Summary of Contents for Centair CMEV.4e

















Reviews: