background image

11b mode; 11, 5.5, 2, 1 Mbps 

 

Turbo mode: 108, 96, 72, 48, 36, 24, 18, 12 Mbps 
11a/11g: Tx: 850mA; Rx: 450mA (max) 

Power Consuption 

11b: Tx: 700mA; Rx: 400mA (max) 

PHYSICAL SPECIFICATIONS 

Dimensions 59.60mm(L)*44.45mm(W)*3.30mm(H) 
Weight <20g 

ENVIRONMENTAL SPECIFICATIONS 

 

Temperature (Ambient) 

Humidity (non-condensing) 

Operating 

0~55

 90

 

Storage 

-20~65

 5~95

 

4. Hardware Installation 

The following sections in this chapter describe how to install AG-622

 

Module 

4.1. Installation Overview 

AG-622 

wireless module is design for PC, Access Point, Router, ATU-R, Printer Server 

series, IP Camera series and Internet Video Server. 

4.2. Safety Recommendations 

The safety guidelines are as follows: 

λ 

Keep the board area clear and dust-free before, during, and after installation. 

λ 

Keep tools away from walk areas where you and others could fall over them. 

λ 

Do not wear loose clothing or jewelry, such as earrings, bracelets, or chains, that 

could get caught in the board. 

λ 

Wear safety glasses if you are working under any conditions that might be 

hazardous to your eyes. 

λ 

Do not perform any action that creates a potential hazard to people or makes 

the equipment unsafe. 

λ 

Never attempt to lift an object that is too heavy for one person to handle. 

4.3. Maintaining Safety with Electricity 

Warning: Before working on a board or working near power supplies, unplug the power 
cord on AC units; on DC units, disconnect the power at the circuit breaker

Follow these guidelines when working on equipment powered by electricity: 

λ 

Do not work alone if potentially hazardous conditions exist anywhere in your 

work space. 

λ 

Never assume that power is disconnected from a circuit; always check the 

circuit. 

extension cables, frayed power cords, and missing safety grounds. 

λ 

If an electrical accident occurs, proceed as follows: 

– 

Use caution; do not become a victim yourself. 

– 

Disconnect power from the system. 

– 

If possible, send another person to get medical aid. Otherwise, assess the condition of 

the victim and then call for help. 

– 

Determine if the person needs rescue breathing or external cardiac compressions; 

then take appropriate action. 

- 7 - 

4.4. 

Installing a 

AG-622 

Summary of Contents for AG-622






Reviews: