Zanussi ZX 57/3 SA, Instruction Booklet

Page: 5 / 24

5
OPERATION
Before using
Remove all securing tapes. Wash inside the
appliance with lukewarm water and bicarbonate of
soda (5 ml to 0.5 litre of water).
Do not use soap or detergent as the smell may
linger. Dry thoroughly.
Setting the temperature
The temperature inside the appliance is regulated by
a thermostat with 6 temperature positions and an
ÒOFFÓ (
●
) position.
Position 1 = minimum coldness
Position 6 = maximum coldness
Turn the thermostat dial to the required position.
The intermediate position is usually the most
suitable (3-4).
The thermostat control regulates the temperature
both within the fridge and the freezer compartment.
The thermostat setting can vary as the temperature
inside the appliance depends on the following
factors:
Ð room temperature
Ð how often the door is opened
Ð how much food is stored
Ð position of the appliance
To Start the Appliance
Allow the appliance to stand for 2 hours after
installation.
Plug in the appliance and switch on at the mains
supply. Turn the thermostat control (A) to a midway
setting (3-4) and adjust the slider control, situated on
the back wall of the fridge section, to a midway
position between ÒcoldÓ and ÒcoldestÓ. The pilot light
(B) will illuminate. Leave the appliance for
approximately 4 hours for the correct temperature to
be reached before placing food inside.
To switch off the appliance turn the thermostat
control to position Ò
●
Ó
Use of an air circulation slider
control - COOL FLOW SYSTEM
Your appliance has an air circulation slider control
situated at the rear of the fridge compartment, which
controls the amount of cold air circulated through the
fridge compartment.
When the ambient temperature is between 10¡C and
16¡C, the slider control should be in the ÒcoldÓ
position.
When the ambient temperature is above 16¡C the
slider control should be midway between ÒcoldÓ and
ÒcoldestÓ.
When the ambient temperature is very high (i.e. hot
summer days) position the slider control to ÒcoldestÓ.
D757
COLD
COLDEST
COOL FLOW SYSTEM
COLD COLDEST
COOL FLOW SYSTEM
A
B
6
5
4 3
2
1
Control panel
A - Thermostat control
B - Pilot light
20
Door reversal directions
1. Disconnect from the electricity supply.
2. Remove all loose items, including food, store
food in a cool place.
3. Gently lay the fridge/freezer on its back with the
top held away from the floor by 5-8 cm (2-3
inches) of packing;
4. Remove the feet (2-3)
5. Remove bottom hinge (1).
6. Remove the freezer door by releasing it from the
middle hinge (H).
7. Unscrew the middle hinge.
8. Slide out the fridge door from pin (G), unscrew
the latter and then screw it down into the hinge
provided on the opposite side, after having
removed the small plugs which should then be
fitted on the opposite side.
9. Refit the fridge door and replace the middle hinge
to the left hand side.
10.Replace the door and bottom hinge (1) on the
opposite side.
11.Refit the feet (2-3) on the opposite side.
Attention
After completion of the door reversing operation,
check that the door gasket adheres to the cabinet. If
the ambient temperature is cold (i.e. in Winter), the
gasket may not fit perfectly to the cabinet. In that
case, wait for the natural fitting of the gasket or
accelerate this process by heating up the part
involved with a normal hairdryer on a low setting.
G
H
D419
Printed on recycled paper
D715 PIED/M
1
2
3