background image

• Open the doors. Un-

screw the middle hinge

(m2). Remove the plas-

tic spacer (m1).

• Remove the spacer

(m6) and move to the

other side of the hinge

pivot (m5).

• Remove the doors.
• Remove the left-hand

cover pin of the middle

hinge (m3,m4) and

move to the other side.

• Fit the pin of the middle

hinge (m5) into the left-

hand hole of the lower

door.

• Unscrew the lower

hinge (b1)

• Remove the left-hand

cover pins (b4) and

move to the other side.

• Re-screw the lower

hinge (b1) on the oppo-

site side.

• Unscrew the lower

hinge pivot (b2) and

the spacer (b3) and

place them on the oppo-

site side.

• Remove the plugs (1)

on the upper side of

both doors and move

them to the other side.

• Re-insert the lower

door on the lower hinge

pivot (b2).

• Insert the middle hinge

(m2) into the left drill of

the lower door.

• Unscrew the upper

hinge pivot and place it

on the opposite side.

• Fit the upper door on

the upper door pivot.

• Re-insert the upper

door on the middle

hinge pivot (m5) slight-

ly tilting both doors.

• Re-screw the middle

hinge (m2). Do not for-

get the plastic spacer

(m1).

Do a final check to make sure that:
• All screws are tightened.
• The edges of the doors run parallel to the side edge

of the appliance.

• The magnetic seal adheres to the cabinet.
• The door opens and closes correctly.

If the ambient temperature is cold (i.e. in Winter), the

gasket may not fit perfectly to the cabinet. In that case,

wait for the natural fitting of the gasket.

In case you do not want to carry out the above men-

tioned operations, contact the nearest After Sales Serv-

ice Force. The After Sales Service specialist will carry

out the reversibility of the doors at your cost.

Environmental concerns

The symbol     on the product or on its packaging

indicates that this product may not be treated as

household waste. Instead it should be taken to the

appropriate collection point for the recycling of

electrical and electronic equipment. By ensuring this

product is disposed of correctly, you will help prevent

potential negative consequences for the environment

and human health, which could otherwise be caused by

inappropriate waste handling of this product. For more

detailed information about recycling of this product,

please contact your local council, your household waste

disposal service or the shop where you purchased the

product.

 

9

Summary of Contents for ZRB934PW













Reviews: