background image

12

UNPACKING AND CONTROL

Please examine the appliance for

any damage sustained during

transportation! If the appliance is

damaged please immediately inform

the forwarding company before the

appliance is connected. The packing

material should be disposed properly.

PREPARATION FOR INSTALLATION

•

Cut out worktop to prescribed measurements or

templates (saw exactly along the scribing).

•

Check seal for perfect fit and overall cover.

•

Lower the ceramic hob into place and align correctly.

•

In terms of fire protection, the appliance conforms to

Type Y (IEC 335-2-6). Only appliances of this type

may be installed on one side of adjacent upright

furniture housings or walls.

Fastening according to Fig. 1

•

Fasten bracket against the underside of the worktop.

•

Using a standard or Phillips screwdriver, tighten the

tension clamps evenly starting at the centre and

moving diagonally, until the built-in rim is tight on the

worktop.

•

Do not overtighten!

•

Do not use an electric or pneumatic screw driver

without an adjustable safety clutch! (pos. 1 - 1.1 Nm)

Fig. 1

Worktop

Seal

Ceramic

Bracket

Summary of Contents for ZME 3043












Reviews: