background image

Installation

During normal operation, the condenser and
compressor at the back of the appliance heat
up considerably. For safety reasons, minimum
ventilation must be as shown in the relevant
Figure.
Attention: keep ventilation openings clear 
of obstruction.

If the appliance is transported horizontally, it is
possible that the oil contained in the
compressor flows in the refrigerant circuit. It is
advisable to wait at least two hours before
connecting the appliance to allow the oil to
flow back in the compressor.

There are working parts in this product which
heat up. Always ensure that there is adequate
ventilation as a failure to do this will result in
component failure and possible food loss.
See installation instructions.

Parts which heat up should not be exposed.
Wherever possible the back of the product
should be against a wall.

If the appliance has been transported
horizontally, it is possible that the oil
contained in the compressor ílows in the
refrigerant circuit. It is advisable to wait at
least two hours before connecting the
appliance to allow tlıe oil to flow back in the
compressor.

Environment Protection

This appliance does not contain gasses
which could damage the ozone layer, in
either its refrigerant circuit or insulation
materials. The appliance shall not be
discarded together with the urban refuse
and rubbish. Avoid damaging the cooling
unit, especially at the rear near the heat
exchanger. Information on your local
disposal sites may be obtained from your
municipal authorities. The materials used
on this appliance marked with the symbol

are recyclable.

35

CONTENTS

GB

Installation

Positioning

Cleaning the interior

Instructions for totally built-in
appliances

Electrical connection

Technical specification

Use

Operation 

Temperature regulation 

Fresh food refrigeration 

Movable shelves

Positioning the door shelves

Defrosting

Maintenance

Periodic cleaning

Extended periods of non-operation

Interior light

Defective operation

36

36

36

37

39

39

40

40

40

40

40

41

41

42

42

42

42

42

Summary of Contents for ZI 7195











Reviews: