background image

INSTALLATION

GB

If this appliance featuring magnetic door
seals is to replace an older appliance
having a spring lock (latch) on the door or
lid, be sure to make that spring lock
unusable before you discard the old
appliance. This will prevent it from
becoming a death-trap for a child.

Positioning

The appliance should be installed well away
from sources of heat such as radiators, boilers,
direct sunlight etc. Best performance is
obtained with ambient temperature between
+18°C and +43°C (class T); +18°C and +38°C
(class ST); +16°C and +32°C (class N); +10°C
and +32°C (class SN). The class of your
appliance is shown on its rating plate.

For building into kitchen units follow the special
“ Building-in” instructions given.

Important

It is essential that the appliance be connected
to an efficient earth tap. For this purpose the
supply cable plug incorporates a special earth
contact. If the sockets of your domestic wiring
system are not earthed, have the appliance
connected to a separate earth wire by a
qualified electrician in accordance with existing
safety regulations.

The Manufacturer declines all responsibility
if the above safety precautions are not
observed.

This appliance complies with EEC directive
number 87/308 of 2/6/87 relative to radio
interference suppression.

This appliance complies with the
following   E.E.C. Directives:

- 73/23 EEC of 19.2.73 (Low Voltage Directive)
and subsequent mod)fications; 

- 89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent
modifications.

Cleaning the interior

Before using the appliance for the first time,
wash the interior and all internal accessories
with lukewarm water and some neutral soap
so as to remove the typical smell of a brand-
new product, then dry thoroughly. Do not use
detergents or abrasive powders, as these will
damage the finish.

39

Summary of Contents for ZI 7164












Reviews: