background image

14

Fitting the Cooker Hood to the Wall

1.

Fit the brackets with the round ends facing
downwards using the plastic rawl plugs and
screws provided.

2.

Once the brackets are secured, lift the hood
squarely to the wall slightly higher than the
brackets. Lower the cooker hood until it is located
onto the two brackets.

Ensure that the cooker hood is correctly
located before letting go.

3.

By loosening the screws in the extension arm
the hood can be aligned with the front of the
adjoining wall cabinets.

4.

The hood should be secured on each side to the
adjoining wall cabinets using the 4 x 15mm (1/2
ins) security screws provided.

5.

Adjust the lower spacer panel at the rear of the
hood to close the gap to the wall.

Decor Panel

The dimensions of the door panel should be
59.6cm (23 1/2 ins) wide by 35cm (13 3/4 ins) in
height.

Fitting a Decor Panel to the Hood
Visor

1.

Remove the complete visor assembly by pulling
open into the operating position, simultaneously
press down on the release catch located behind
the visor on the left hand side of the casing.

2.

Using the paper template provided, mark the
screw hole positions on the reverse side of the
decor panel. Ensure that the paper template is
aligned with the top edge of the decor panel.

Summary of Contents for ZHI 600





















Reviews: